Jump to content
SAU Community

Recommended Posts

I just realized, theres never been any mention of earthquakes in the Japan forum...

Well, the Kansai area and most of western Japan got hit by 2, yes 2 earthquakes tonight:

quake.040906001957.03.5.gif

震度7pin8.gif震度6強pin7.gif震度6弱pin6.gif震度5強pin5.gif震度5弱pin4.gif震度4pin3.gif震度3pin2.gif震度2pin1.gif震度1

My area and dare I say Troys area too got hit by a level 3 or 4, while Mie (where I used to live) got hit by a level 5 intensity on the Japanese Omori scale.

What made tonight interesting was that we had 2 quakes, both within 2 hours of each other, both the same intensity, and both lasting at least 15 - 20 seconds (in Hyogo). Usaually a larger one is folowed up by aftershocks of a lower intensity... but then again I'm no goelogist so this might not be so uncommon, I don't know.

Tidal wave warnings are in effect from Tokyo right across to Shikoku, with the main focus on the Mie prefecture area (where the epicenter was, some way off the coast).

Anyways, thats enough action for one night, I'm off to bed.

Link to comment
https://www.sau.com.au/forums/topic/50373-earthquake/
Share on other sites

I was in saitama tonite and felt a very small quake around 6:30pm

They have been happening on and off a fair bit recently in tokyo..

last week i was on the 7th floor at my school and one hit.

Maybe someone should post up some info regarding the great kansai prediction... similar but more power than the Kobe earthquake... that is expected to hit sometime soon. and destroy 6 million out of the 6.6million structures in the area.

Link to comment
https://www.sau.com.au/forums/topic/50373-earthquake/#findComment-1000848
Share on other sites

Maybe someone should post up some info regarding the great kansai prediction... similar but more power than the Kobe earthquake... that is expected to hit sometime soon. and destroy 6 million out of the 6.6million structures in the area.

Whats this about? Do tell

Link to comment
https://www.sau.com.au/forums/topic/50373-earthquake/#findComment-1001960
Share on other sites

Just got woken up by another one... this is getting a little freaky now, as there is a typhoon coming our way later on this afternoon too, and as you can see the epicenter is in almost the exact same place...

quake.040907083453.03.5.gif

pin9.gif震度7pin8.gif震度6強pin7.gif震度6弱pin6.gif震度5強pin5.gif震度5弱pin4.gif震度4pin3.gif震度3pin2.gif震度2pin1.gif震度1

This time the highest magnitude was 4 in Mie (again), and we acyually felt a level 3. It only lasted for 5 - 10 seconds, but still, in my time in Japan this is the first time I felt 3 quakes within days of each other... something must be brewing underground?

Link to comment
https://www.sau.com.au/forums/topic/50373-earthquake/#findComment-1002194
Share on other sites

Damnit... Japan will be destroyed before I get over there. :P
Hehehe, you know, sometimes I think Japanese people want Japan to be destroyed, just so they can start over again...:headspin:
Link to comment
https://www.sau.com.au/forums/topic/50373-earthquake/#findComment-1002319
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...