Jump to content
SAU Community

Recommended Posts

  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

Ever heard the saying that a $2 part always caused the problem? :D

5000km is alot for a high strung engine, so you are better off spending the extra $5 for filters like ryco rather than have to spend $2000 on an engine rebuild after using cheap filters and oil

just because its more expensive doesn't mean its any better

you show me conclusive testing results saying that the filter twice the price is better and i will use it...

if you are going to re-oil your fitler then you might also want to get some carby cleaner (i use brake cleaner) to clean your AFM.

after you oil the filter some will travel through and onto the wire in the AFM so a few days after service it wouldn't hurt to give it a spray...

cheers,

Waz.

Do not forget to gap your sprak plugs

the bcpr6es is the model number and 11 is the gap you should gap them to 1.1 mm but on a turbo car you might go down to .8 depingding on boost..

They used to come pre gapped to 1.1 now you have to set the gap yourself

Would a 0.8mm gap on regular copper plugs in a stock engine be alright?

hey adam,

if you're running stock boost then i would stick with the 1.1mm gap for better combustion

from what i understand, 0.8mm gaps are for when the boost is turned up over stock levels

the way i see it if small gaps did nothing at all bad then all plugs would be gapped down to 0.5mm or so. the smaller the gap eventually must do something (i have heard that the larger the gap the better the fuel ignites and it combusts more efficiently or something).

moral of the story (in my opinion): run as big a gap as your engine will allow without missing :)

cheers,

Warren.

Thanks Waz just one more thing, can having the gap too small do any damage?

dunno

have heard that you can get pinging but have not had any first-hand experience so not 100% sure

i have a theory that if you gap it too small then you will begin to lose some power but as i said jsut atheory

INASNT - wow didn't realise the fuel filter was so cheap! wil get onto that myself!

cheers,

Waz.

If the gap is too small it will sound like marbles are rolling around in the engine (i.e a few cylinders wont fire). You will notice this as soon as the car is started.

If you have an exhaust the boost usually creeps up a few PSI so gapping to 0.9-0.8 could be an idea.

Ryco Fuel filters are around $20-25 from kmart for a Z200 - Z201/Z202 [bigger] I bought one about 12 months ago and will be replacing soon, I think the box said 15,000kms or 12 months [whichever comes first].

I dont know where you can get RYCO for $12 Denham?

Ryco Fuel filters are around $20-25 from kmart for a Z200 - Z201/Z202 [bigger] I bought one about 12 months ago and will be replacing soon, I think the box said 15,000kms or 12 months [whichever comes first].

 

I dont know where you can get RYCO for $12 Denham?

See attached photo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I don't think the shuffle can damage the turbos. It only happens at low shaft speeds and loads. It's just annoying (to some people - others are tickled by the effect) and it quite possibly reduces spool performance a little bit.
    • Oh dear. The panel beating needs to be done before the filler work. Do you have a photo of the dent before you started? Hard enough to not flex and only hit the high spots?  What do you mean it was just temporary? 
    • Can u check this way it works for power supply?
    • These coils draw 10amps that what i read online
    • I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
×
×
  • Create New...