Jump to content
SAU Community

Another skyliner is born....

NismoGirl

By NismoGirl,
in Queensland

 Share

Recommended Posts

NismoGirl Grand Master

NismoGirl

Posted
Posted

I would just like to say congratulations to both Warwick and Jules on the birth of their baby boy. :gaga:

Name: James Richard

Born: 7:18pm on 21st September 2004

Weight: 8lb 15oz

Mum, Dad and bub are all doing well but are very tired.

Congratulations Warwick and Jules! :P Welcome to the sleepless nights, constant cries and pooey nappies :D

Well done!

Piccie:

james_richard.jpg

Link to comment
https://www.sau.com.au/forums/topic/51707-another-skyliner-is-born/
Share on other sites
Oz Grand Master

Oz

Posted
Posted

yep :P Congrats Warwick and Jules & a big hello & welcome to the world to new :gaga: bubby james

WRX's make such good family cars too ;)
Don't they just chris, rex c even the name says its a family car for the family & the dog "Rex"
Lazy-Bastard Grand Master

Lazy-Bastard

Posted
Posted

Thanks to everyone for all the well wishes.

Already learning what the sleepless nights are about...have had about 6 hours in the last three days, so training has begun.

Jules and baby are still at the hospital but should be home in the next day or so.

They have graciously thrown some cardboard and newspaper on the floor for me so I am staying there most of the time and just popping back home to "freshen up" every now and then.

See you all in about 20 years :D

And just for the record, the baby seat fits better in the 'line than in the WRX ;)

:(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Songo
      New kid on the block

      By Songo · Posted

      Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • MBS206
      New kid on the block

      By MBS206 · Posted

      https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
    • Cangorus
      New here

      By Cangorus · Posted

      Hello everyone, I am happy to join you.
    • Duncan
      New here

      By Duncan · Posted

      Whereabouts are you, that looks exactly like Akira's old car....
×
×
  • Create New...