Jump to content
SAU Community

Recommended Posts

Winged/Gated sump is where the sump has one or two flaps which act as trapdoors to prevent oil starvation by the oil pump. Usually fitted by drifters and racers because the violent movement of the oil whilst racing adversely hinders oil pickup.

Link to comment
https://www.sau.com.au/forums/topic/52561-busted-sump/#findComment-1035481
Share on other sites

If you have a RWD GTST then id stick with using the std sump, unless fo course you have spare cash tehn sure go ahead but i think there are other areas of the std RB engine that need help before the sump. LOL, also keep in mind that with a bigger sump a simple thing liek your regular oil change may add up to $100+ due to the capacity increase:(

Link to comment
https://www.sau.com.au/forums/topic/52561-busted-sump/#findComment-1035934
Share on other sites

I might be wrong...so call me stupid :)......

I think the engine has to come up or out to take it off...the oil pickup sits into the pan a bit though a hole into the bottom...

Bit of one of those jobs that are a pain in the butt.....like every god damn thing else that needs fixin :bahaha:

Link to comment
https://www.sau.com.au/forums/topic/52561-busted-sump/#findComment-1036049
Share on other sites

Im not sure on the GTS models but on the GTR it can be done without removing the engine, however at the end of the day it will cost you around the same in labour. Involves pulling the gearbox off, removing the front cross member while holding the engine in place with an engine stand, quite alot of work.

Link to comment
https://www.sau.com.au/forums/topic/52561-busted-sump/#findComment-1036155
Share on other sites

nar u shuldnt hav 2 take the motor out, easier 4 gtr coz frnt diff goes thru the sump.

dnt quote me, but the last time i checkd, u jus take out all lil sump bolts (10mm) n the 2 reinforcing mounts on eithr side 2 bolts on box n 2 on motor eithr side (12/14mm soz cant membr), n the gbox cover plate to make it easier 2 get 2 bak bolts, may need screwdriver 2 break seal ov factory glue (dnt scrap hole in sump/block) n then a bit ov manouvoring around the oil pick up inside n the cross membr underneith n then wolah! off.. but youl proly find u might not b able 2 get 2 the dent, proly hav baffles in ther, but cant hurt lookn. GOOD LUCK.

Link to comment
https://www.sau.com.au/forums/topic/52561-busted-sump/#findComment-1036156
Share on other sites

Ok, Ill take a shot at it tomorrow - Just a warning that I have no idea what i'm doing..

- Take out All the 10mm Sump Bolts

- Take out 2 Reinforcement Bolts (Located at the front?

- Take out 2 bolts on box (Where ever these are?)

- Take out 2 Bolts on motor either side (12/14mm) (Again, whereever these are?),

- Take off Gearbox Cover Plate

- Take out Back two bolts

Think thats what you were trying to say in your instructions :)

Link to comment
https://www.sau.com.au/forums/topic/52561-busted-sump/#findComment-1036257
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...