Jump to content
SAU Community

Recommended Posts

*HKS Graphic Control Computer--(HKS PFC F-CON) and wiring

http://www.hksusa.com/products/?id=688 ...........$400

*HKS Injection Pulse Monitor (good with the F-Con).

http://www.hksusa.com/products/?id=729&rsku=0 .........$150

OR BOTH for $500

*Genuine 33 Vspec standard shocks..........$350

*824 pages of photocopied GTR manual..........$30SOLD

*Genuine 32 GTR side skirts (plastic) with spats (or whatever you call them), could use a paint but I guess youd have to if you didn't have a grey car anyhow..........$350Back on the market thanks to tire kicker

*1 orange GTST indicator, leftover stuff from previous car..........$15

*Pair of orange GTR side indicators..........$30

*Prefabricated 1 cubic foot 12" sub box..........$15

*2 x framed pics of Skaifes no. 2 wining bathurst GTR

1 in 34 x 24 cm frame and 1 in 30 x 40 cm frame..........$35 eachSOLD

*Standard GTST BOV..........$15

*Blitz Badge..........$20

*Carrozeria (jap pioneer) 6 stacker and head unit..........$50SOLD

*QLD personalized plates

40RCN, silver on blue..........$1000

GTR44, silver on black..........$470

51CKR, silver on purple..........$650

[email protected]

About the HKS GCC:

The GCC is an electronic tuning component designed to add additional flexibility to the fuel tuning capabilities of the VPC, PFC F-CON or F-CON S. The GCC simply plugs into either the VPC or F-CON harness and allows the user to further adjust the air / fuel ratio at five specific rpm points. Each five points offer an adjustment range of 16% rich to 12% lean, in 2% increments, of the base value. Four different selectable rpm ranges allow maximum rpm level flexibility when tuning the fuel curve. The GCC will interpolate, or average between the rpm points of adjustment to ensure a smooth transition of fuel delivery throughout the RPM band

and the IPM:

The HKS Injection Pulse Monitor, or IPM, is an electronic injector duty cycle monitor and display unit. When tuning a fuel system with an HKS Graphic Control Computer (GCC), VPC, F-CON, AIC III or Super AFR, the IPM is essential for determining the remaining fuel injector capacity. With the supplied wiring harness, the IPM plugs directly into any vehicle equipped with an HKS PFC F-CON (Programmed Fuel Computer) or can be wired directly into the stock ECU harness of any electronically fuel injected application. When used with the PFC F-CON, the IPM will show the difference between the factory specified pulse width vs. that of the HKS F-CON pulse width on its dual level LED display. When used with the stock ECU, two separate injector signals can be displayed on the dual level LED display, either two stock injector signals or one stock injector signal and one signal from an AIC injector. As the injector pulse is increased via fuel controllers, the IPM will display the new injector duty cycle in real-time. In addition to monitoring, the IPM incorporates an audible alarm that can be set to trigger when any pulse width from 50% to 95%, in 5% intervals, is reached

Firstly Ricknismo is a great seller, so enjoy the bump :D

Secondly, Rick do you still have one of the skaiffe GTR pics? If so, I'll take one.

Regards,

Richard

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...