Jump to content
SAU Community

Recommended Posts

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

I saw a Stagea run an 11, that's a fast boat.:)

Hi Have you towed any of the race cars yet with the Stagea?

Used your suggested suspension settings on my R33 track car's first outing....result very good, pretty neutral handling with good front end turn in. thanks :D

Hi    Have you towed any of the race cars yet with the Stagea?

 

 Used your suggested suspension settings on my R33 track car's first outing....result very good, pretty neutral handling with good front end turn in.   thanks :D

Good to hear, you need to fine tune the settings to your personal tastes, but it's a good place to start. As for Stagea towing, I haven't found a tow bar with enough capacity yet, still looking

:)

  • 3 months later...
Yeh when is the Winton UAS day? Im in melbourne and will be trying to convince some of the hillbillies down here to make the trip north for the weekend...:(

Could get down there one day although more likely to go to Qld. Waiting for my custom trailer to be finished.

The boat is getting pumped even more. Found the valves were badly worn from too much boost and not enough valve spring pressure even though the springs were twice factoryspec. Now have Supertech .5mm oversized valves. Found Arias chrome rings not best for high temp and boost as they wore out, so going 40 thou oversized Ross pistons with full steel rings gas nitrided and proven in big boost drag cars. All cryogenic treated. Changing turbo's from S15 to Disco potato GT28RS 440hp each. Getting the exh housings high temp HPC coated and if have time will get comp housings extrusion honed. Should make 450rwkw with if anything a little more lag which won't hurt it. Might even get semi slicks on to keep things more honnest hey FATZ?

  • 4 weeks later...

Next UAS track Sunday 1st May Wakefield and keep your eyes on your mirrors please.

Roy Porsche 6 piston GT3 Carrear cup Monoblock's lightwieght, brand new can do $800 each. Second hand $650 each. I know you would use them.

  • 3 weeks later...

Put new motor in and new D2 suspension and went to Nissan Datsun Nationals Easter Sunday at Wakefield. Only got three runs on the full circuit and only managed a 1 min 9.48 although still fastest car on the day next fasted was a Dato 120y coupe FJ20 near 200rwkw 900kg 2 seconds slower. Heaps of zeds and a few Skylines and a R32 GTR. Got back and pulled motor out Tuesday to remove turbo's to get extrude honed and high temp coated and a few other minor changes then going back in next few weeks ready for our track day. Bring on your GTR's or GTS-T's.

PS more GTR parts as now has GTR bronze valve guides and valve stem seals. We measured and found the valve guides to be slightly shorter and protrude less into the ports so less restriction and proven on flow bench test.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...