Jump to content
SAU Community

Recommended Posts

SK, have you any info on my items as they haven't arrived as yet.  I did send you a PM but you may not have got it.  It has be over two weeks now, just want to know if there is any drama as it is probably just the frieght takng its time as usual to Darwin.

Cheers ICE.

Hi Ice, has it arrived OK? If not, you can check its progress on the Toll website, just use the con note number I PM'd you.

:) cheers :)

  • 2 weeks later...

G'day Happymeal, I have just bought a 98' stagea that has a leaking front shock and sounds like they are bottom out. It rides bumps in the road like a pogo stick. It has been lowered about 30mm in the front and 20mm in the back, on black HKS coils.The shocks are pedders so I found out what is in it and I was told r32 gtr. They are 16mm shorter on extension, 6mm shorter compressed and the stroke is 20mm shorter, than r33 gtr. That conflicts with what I have read on these suspension pages, saying we should use r33 gtr. Did you sort out what model shock you needed?

G'day Happymeal, I have just bought a 98' stagea that has a leaking front shock and sounds like they are bottom out. It rides bumps in the road like a pogo stick. It has been lowered about 30mm in the front and 20mm in the back, on black HKS coils.The shocks are pedders so I found out what is in it and I was told r32 gtr. They are 16mm shorter on extension, 6mm shorter compressed and the stroke is 20mm shorter, than r33 gtr. That conflicts with what I have read on these suspension pages, saying we should use r33 gtr. Did you sort out what model shock you needed?

So far 6 Stageas fitted with Group Buy kits, so can confirm the following;

R33GTR front will fit, valving may be OK depending on shock quality

R33GTST rear will fit, valving is not OK.

:huh: cheers :)

  • 3 weeks later...

For anyone that slides around in the wet, the suspension kit is a MUST.

Before the car has pretty crappy weight transfer and i was opposite locking a lot. From lock to lock to lock to lock. Now the baby just slides soooo smooth. I can hold bigger, longer, more angle slides with much much less stress.

Good work!

Hey Guy's after receiving my stagea i found out it had aftermarket suspension. can anyone tell me about GAB Sports coilovers? I know the fronts have 4 dampening adjustments in the top, dunno about the back.

Don't know much about GAB's for Skylines. I have replaced a few in Hondas though. Very harsh, big spring rates, twin tube shock design so small piston area etc. In summary, a fairly basic, low cost, Jap coil over. See how they feel for you, they will accept lower spring rates, that does improve the ride and handling a little.

:P cheers :)

  • 1 month later...

ok, just need to know if l'm right here.

I can use:

fronts - R33 GTR shocks

rears - R33 GTST shocks

on the stagea right?? I have a set of springs l want to put in, but don't want to do it using stock shocks.

Or is there another option rather than the bilstein's ... something around the 100-125 a shock area?? atm l can't justify spending anymore than about $500 on it all, my finance's just won't stretch the far unfortunately. :D

Edited by [ STAGEN ]
  • 4 weeks later...

A lowering question, pretty much aimed at SydneyKid, but happy to hear from anyone(!).

Your method of lowering via latheing more circlip grooves down the strut body, can this be done when using the standard Stagea shocks? Or is that option only available if you upgrade to Bilstein or similiar? Would naturally like new shocks, but still paying car off, so low cost mods only for me at the moment.

Thanks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...