Jump to content
SAU Community

Recommended Posts

The AFMs in my GTR are maxed out. Is there any alternative to running Z32 AFMs? The reason I ask is that I would like to retain the stock air box. I don't want to fit pod filters. I think I have seen NISMO AFMs. I'm assuming these will bolt straight in and even plug straight in? I don't know where to buy them from though.

RB26 AFM's are 65mm ID, RB20/25/Z32 AFM's are 80 mm ID. What R32-GTS is saying is, the electrical connectors are the same on RB20 and RB26 AFM's so "they"plug straight in". The standard rubber hoses from the turbos will stretch to fit the larger OD. But the AFM's won't bolt up to the standard air box. If you have pods then just upgrade the bases to RB20/25 ones.

Hope that helps :rolleyes:

RB26 AFM's are 65mm ID, RB20/25/Z32 AFM's are 80 mm ID.  What R32-GTS is saying is, the electrical connectors are the same on RB20 and RB26 AFM's so "they"plug straight in".   The standard rubber hoses from the turbos will stretch to fit the larger OD.   But the AFM's won't bolt up to the standard air box.  If you have pods then just upgrade the bases to RB20/25 ones.

Hope that helps :rolleyes:

if so, then how come every one is after the Z32 FMs?? since RB20 AFMs are fit??

arent they cheaper too??

dont mean to hijack, but would a GTR33 benfit from such an apgrade if it was stock with mearly some basic bolt-ons??

if so, then how come every one is after the Z32 FMs??  since RB20 AFMs are fit??

arent they cheaper too??

dont mean to hijack, but would a GTR33 benfit from such an apgrade if it was stock with mearly some basic bolt-ons??

Replacing an RB20/25DET AFM with a Z32 AFM is a worthwhile upgrade if the RB20/25DET AFM is reaching its max voltage and causing tuning problems as a result. This seems to have flowed over to GTR's even though it isn't really necessary in most cases. After all why worry about spending a couple of hundred dollears extra on Z32 AFMS compared to RB20/25 AFM's? Many people spend tens of thousands on their GTR upgrades, so what's a couple hundy here or there?

Plus why take a risk, they might make enough power to max out the RB20/25 AFM's. Just buy the biggest and baddest and not worry about it. Perosnally I prefer to buy the right size for the power target, this table may help;

Rule of thumb for Air Flow meters RWKW & Engine BHP

------ ---- OD ---- RWKW ---- RWKW ---- BHP ------ BHP

No of AFM's ---- ------- 1 -------- 2 -------- 1 -------- 2

RB26 ------ 65 ------ 149 ------ 299 ------ 271 ------ 474

RB20/25 --- 80 ------ 226 ------ 453 ------ 376 ------ 683

Z32 ------- 80 ------ 255 ------ 511 ------ 415 ------ 763

Q45 ------- 90 ------ 302 ------ 605 ------ 479 ------ 890

Please note that this is only an indication, every engine is different and tuning makes a big difference. For example, I have seen a GTR equiped with twin Q45 AFM's make 1100 bhp.

RB20/25 and Z32 AFM's are all 80 mm OD, that's outside diameter, not ID that's inside diameter. There is no real difference between an RB20 and an RB25 AFM. On the other hand the Z32 AFM is calibrated differently, so at the airflow the RB20/25 AFM shows max voltage, ~5 volts the Z32 afm is only showing ~4 volts. This means when the airlfow gets higher the Z32 can still show voltage increases to the ECU.

Q45 (Infinity) AFM's are 90 mm (OD), so they have the same calibration advantage but they are also larger in diameter for less restriction.

Hope that helps:cheers:

Well the RB20/25 ones would be easier to fit, so I don't have to butcher the looms.

But, I really didn't want to fit pod filters. I guess there is no other way.

Does the GTR power FC have the RB20 AFMs in it's table of AFMs?

Are there any 65mm AFMs with a higher load resolution?

i fitted rb20 afm to my gtr r33 and the pfc has a selection for rb25 afm which worked a treat for me a i believe there is next to no difference and i am running over 500 hp at the wheels so unless you want to go over about 550hp at the wheels the rb20/25 will be fine

and i have heard of guys doing small mods to air bow to make them fit both rb20/25 and z32

i fitted rb20 afm to my gtr r33 and the pfc has a selection for rb25 afm which worked a treat for me a i believe there is next to no difference and i am running over 500 hp at the wheels so unless you want to go over about 550hp at the wheels the rb20/25 will be fine

and i have heard of guys doing small mods to air bow to make them fit both rb20/25 and z32

Do you run the air box or pod filters?

What about the RB30E air flow meters (VL and R31). Are they the same as a Z32?

1.Well the RB20/25 ones would be easier to fit, so I don't have to butcher the looms.

2. But, I really didn't want to fit pod filters. I guess there is no other way.

3. Does the GTR power FC have the RB20 AFMs in it's table of AFMs?

4. Are there any 65mm AFMs with a higher load resolution?

1. You don't have to "butcher the looms" I splice in the larger AFM wiring harness in parrallel tothe standard plugs. This means you can swap back to the std AFM easily.

2. ARC (and probably others) make an airbox that fits the 80mm AFMs. You can modify the standard airbox, basically you just cut out the 65mm flanges and replace them with aluminium sheet for 80 mm. Sounds hard/shonky but looks good when finished. I have some pictures somewhere of one modified, I will try and find them.

3. Yes

4. Yes, there a few Jpanaese tuning shops that used to make them, swap the Z32 hot wire in to the GTR AFM body. But they aren't very common, most people went for the cheaper and more effective 80mm option.

Hope that helps :rolleyes:

ARC make a really nice aluminum or carbon fibre replacement box for 80mm Z32 afm. I just did the upgrade and without any other modifications except for Z32 AFM and power FC tune i saw an increase of 60 RWHP.

I bought my Z32 AFM brand new in boxes from www.nengun.com for $449 per afm, that is unbeatable price for brand spanking new AFM. He threw in the tomei adaptors so there was no butchering at all. Apexi PowerFc has a function to run the Z32 afm, so i dont know why you would consider doing anything else, all of the hard research has been done for you. Z32 work well and consistently and at the nengun price they are cheaper than most second hand half shit afm's.

TG

  • 4 months later...

So the smaller throat diam of the GTR AFMs makes no difference.

Another thing a friend did, that i also see on Jap cars is remove the hot wire sensor from wahtever AFM you are using and simply drill a hole in your inlet pipes to suit. Some good resin to seal it, onto the pipe, and away you go.

If i go twin with RB26 head thats all i was going to do with the Z32 or Q45 AFM with the std RB20 Pfc. But i was going to try and put the full AFM in the pipe from the intercooler to Inlet plenum, figured the AFM may even read more accurate as it is sensing the cooler air post intercooler...would have to extend the wiring though...ppls thoughts?

ARC make a really nice aluminum or carbon fibre replacement box for 80mm Z32 afm. I just did the upgrade and without any other modifications except for Z32 AFM and power FC tune i saw an increase of 60 RWHP.

Slightly OT, but does the ARC airbox run the same (sized) filters as the standard airbox, or does it have its own special ARC items?

LW.

So the smaller throat diam of the GTR AFMs makes no difference.

A 65mm orifice can flow "xxx" litres per minute, under 20 psi supply pressure.

2 x 65mm orifices will flow similar to a single 90mm orifice, which incidentally is the inlet and outlet diameter of the intercooler. (from memory the inlet of the plenum as well)

An 80mm orifice will flow "xxx" lt/min @ less supply pressure, so it could be argued that they are less of a restriction. However, what is the benefit of fitting larger AFMs and leaving everything else stock sized ? It would be like expecting HP gain from a 4 inch hotdog on a 3 inch exhaust.

lwells,

AFAIK, ARC box for a GTR has two filters. One is similarly sized to standart filter, the other is considerably larger.

The biggest downfall of them is that, they are not sealed on top.

This is judging by the photos on their website.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...