Jump to content
SAU Community

Recommended Posts

Caught up with the dark green Stagea, S1, also an M35,250t, RS4. Silver, lowered with nice wheels. Thats three on the mountain today caus I saw my wife drive off to work.

Where did you see the M35? Might have been me?

5941448.jpg

I saw a yellow S2 today on the GC Highway outside Australia Fair. I waved but don't think you saw me.

Edited by euroequip
Where did you see the M35? Might have been me?

5941448.jpg

I saw a yellow S2 today on the GC Highway outside Australia Fair. I waved but don't think you saw me.

Either the missus or pipster outside aussie fair, what time was it?

Been seeing pipster everywhere lately!

not me at aus fair

been getting about tho :D

You've driven past me 3x times in southport whilst outside work, I keep thinking its my missus!

I'm keen for this sunday but stuck at work til 7pm, make sure you all beep as you go by southport pool!

You've driven past me 3x times in southport whilst outside work, I keep thinking its my missus!

I'm keen for this sunday but stuck at work til 7pm, make sure you all beep as you go by southport pool!

yeah, sometimes i say with the gf up at hollywell and often go down that way

where do u work?

yeah, sometimes i say with the gf up at hollywell and often go down that way

where do u work?

Tom, did you used to park near that new office block in Nerang opp the tennis courts or near by? Use to see a yellow one there butt never found out. Hav'nt seen it for a while.

Tom, did you used to park near that new office block in Nerang opp the tennis courts or near by? Use to see a yellow one there butt never found out. Hav'nt seen it for a while.

My missus was working opposite tennis courts, has now moved up the road, but still uses fenix gym in the new prana centre.

My missus was working opposite tennis courts, has now moved up the road, but still uses fenix gym in the new prana centre.

i saw her in miami last night, its nearly identical lol

My missus was working opposite tennis courts, has now moved up the road, but still uses fenix gym in the new prana centre.

So yours is yellow too, like Tom's? :) LOL. Mine is green. :)

Hey! Mt Tamborine must surely have regained the title of Stagea Capital of Oz, per capita.

Saw my fifth one of the week, a white S1 with Vic plates parked opposite The Cheese Factory and Brewery on Mt Tamborine.

Spotted a white stag in Westfield Paramatta today.

Accidentally left a note saying:

"Spotted

SAU

From Midol & Spotta"

on his windscreen.

Total accident.

Also saw another white stag while we were lost so not sure where :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...