Jump to content
SAU Community

Recommended Posts

waste of money for the motec, stroked motor, forged internals, custom plenum, twin bosch pumps and surge tank, you dont need all that stufff to run 10s,  

all you would need is injectors, 044 fuel pump, cams, bigger turbo(s) power fc, cooler, standard box is fine, and some good slicks you should get into the 10s with a few passes, then after you get into the 10s then you have to spend big bucks to get back on the track.

I know, I think my mind is set on 9's :/ But can just run it on low boost for easy 10's ;)

I agree with BU5TER, and that was the underlying point I was making. One time wonder or long time contender?

Butler, could you please let me know any info you have regarding the Apexi cranks/stroker kits as I can't seem to find any info on them.

TIA.

Charlie

You need 450rwhp and a good clutch and reasonable tyres.

Jade fishers R33 has Arias pistons ( all origional parts went back in inc the old bearings),smallish ITS plain bearing turbo and Wolf plugin ECU and ran 11.1 all last season with not one problem.

Single throttle kit going on now and i think 10s will be easy this season.

2530's you aint running pump fuel for 400kw

anything is possible if your not running  PULP

Straight Av gas.., around 100 octane. And that is not suppose to be the best. Have to when the best fuel here is 96.. and it's no good.

Be interesting to see what it would go like with some C16.

It's a testament for the GTR engine though, and it has done more than a few 10's runs without failure... I would call that consistent.

Not only that is was a daily driven street car.. damn I miss her :/

A note on the Trust 6 Speed box.. we removed it from the GTR running a T88 to repair it, he couldn't run good times with it.

With a stock box, he didn't have a problem running 10's. ;)

I hated driving the dog box on the street, it's just a major pain in the ass. They don't like to change at low RPM.

I'm struggling to get my 32R into the 11's let alone 10's and power so far is 370rwhp on paper and going off other cars should be into the 11's easy but it's not . Best run so far is 12.1@114mph with a 1.760ft , it comes down alot to your tuning as it's not alway outright horsepower that gets low ET's something that I've realised and am looking to correct.

I'm struggling to get my 32R into the 11's let alone 10's and power so far is 370rwhp on paper and going off other cars should be into the 11's easy but it's not . Best run so far is 12.1@114mph with a 1.760ft , it comes down alot to your tuning as it's not alway outright horsepower that gets low ET's something that I've realised and am looking to correct.

Hi 7heavn

Unfortunately the best times for a GTR are achieved with a "brutal" launch (this makes me cringe every time I do this to my R). Your 1.7 60' time suggests that you are probably not bogging down on launch (your at 6 to 7k before side stepping the clutch, right?).

You are right about the tuning - if you have adjustable cam gears and have dialed in for max hp (at the expense of mid range tourque), you may be dropping off below the max torque in between gear changes. A dyno graph showing power and torque vs revs would help.

I was previously rattling off 12.5s with only 320 rwhp (std terbs) fairly consistently with 1.9 60' times. It sounds like more practice (and maybe a little cam timing adjustment) will see you crack 11s fairly soon. Remember to pre-load the drivetrain using the handbrake and take that 2nd to 3rd change E-A-S-Y.

Good luck.

id think bout changing diff gear sets also, to maybe 4.3 like the gts4 has

my 32 gtst wasnt the same with 4.11's the 4.3's bring the 26 to life over the quarter.

my 26 has 272 cams NO internals and a big single turbo its run best now of 11.1 @ 126mph im sure as is 10's are possible.

My wifes GTR ran 12.0 @ 119.34mph with me being very soft on her car, as you can see 119.34mph means strong 11s driven hard.Her car had a cat back, gmax clutch and a Wolf plugin using the stock AFMs but nothing else. 338rwhp.

We have removed the AFMs now and and ive been told by the boss to take it to the plex again and not to come home with out some strong 11s so ill see what it can really run.

Hi 7heavn

Unfortunately the best times for a GTR are achieved with a "brutal" launch (this makes me cringe every time I do this to my R).  Your 1.7 60' time suggests that you are probably not bogging down on launch (your at 6 to 7k before side stepping the clutch, right?).

You are right about the tuning - if you have adjustable cam gears and have dialed in for max hp (at the expense of mid range tourque), you may be dropping off below the max torque in between gear changes. A dyno graph showing power and torque vs revs would help.

I was previously rattling off 12.5s with only 320 rwhp (std terbs) fairly consistently with 1.9 60' times.  It sounds like more practice (and maybe a little cam timing adjustment) will see you crack 11s fairly soon. Remember to pre-load the drivetrain using the handbrake and take that 2nd to 3rd change E-A-S-Y.  

Good luck.

Hey

Yep 6500rpm sidestep the reason I mentioned the 60ft is just to clarify that not much is being lost at the bottem of the track you see 370rwhp and 114mph through the traps doesn't make sense . My mph should be something closer to steve-sst's wife's car . Only other thing I can think of other then tuning is mine is a vspec is the gearing differen't?.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
×
×
  • Create New...