Jump to content
SAU Community

Recommended Posts

Well... it was pretty much as i suspected.

Found out the radiator is a larger aftermarket unit...

ECU is a standard R33 GTR ECU...

Sam took me for a drive (Dr_Drift) in it... well... now i know what it can do in the right hands hahaha when we got back i was a little shakey and in need of some new underpants but soon got over it :(

We finally got to put it on the Dyno and had a couple of runs... second one blowing a nice little flame but was restricted by the mixture reader in the exhaust pipe... so... we took it out ;)

and this happened :)

414flameon.JPG

http://www.skylinesaustralia.com/photopost.../414flameon.wmv - right click save as ;) its not the greatest quality but i cant actually get the video off the camera and on to the HDD so it will have to do.

Now down to the numbers :(

The car made 207rwkw on 9PSI :)

472nm torque.

Not bad figures for a stock GTR engine.... in a 1350kg cefiro ;)

Link to comment
https://www.sau.com.au/forums/topic/54326-cef-zla-was-dynoed-today/
Share on other sites

lmao guys seriously i bloody would if i could :P

taking it to calder park this friday to see what it can do down the strip just to make it even harder for me to let it go lol :D

but nah... it has to go.

dunno if u can read it all but its the first pic in my gallery :P

Do you know what kind of air/fuel ratio you were getting before you took the meter out of the exhaust? Or wouldn't it be accurate if it was restricting the exhaust?

BTW - do you only have a 2.5" exhaust or is the dyno sheet wrong?

:jump: :D

i dont know if i can get there on friday now... i cannot borrow any of the cars with tow bars cause theyre going away for the long weekend down to a friends holiday house in sorento and taking the boat... plus i dont think i can get the car trailor from a friend.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...