Jump to content
SAU Community

Recommended Posts

After a swift run thru the local "Nasho" i was towed out on the back of a truck.

With my brother driving i watched the temp gauge climb past the point of concern and into the worry area. As i suggested to back off a very loud BANG! interuppted me followed closely by lots of green fluid and steam from under the bonnet.

With the wounded skyline at rest and the bonnet up I noticed there was no top on the radiator anymore.

The results of the post mortum concluded that a sludged up 2nd hand engine had clogged up what was otherwise a clean but 15 year old plastic radiator. With its hire pressure Tomei radiator cap still firmly attached to the now seperated top tank it is certain that these caps hold more pressure than a skyline radiator is designed for.

The moral to the story is:

1. flush your cooling system thoroughly after installing a 2nd hand engine

2. pay more attention to your engine temp

3. only use high pressure rad caps on high press rads

Bye all. :kick:

Link to comment
https://www.sau.com.au/forums/topic/54409-radiator-went-bang/
Share on other sites

I had a little pin hole leak in my rad but didn't notice it warming up until the ECU decided it was time to shut down :( engine was fine so thank god for that.

It did look like some alien had climbed under the bonnet tho, green goo everywhere!

I think point 3 is pretty important, in a lot of ways a high pressure cap shouldnt be required if the rest of the colling system is working ok :)

I had a little pin hole leak in my rad but didn't notice it warming up until the ECU decided it was time to shut down :P engine was fine so thank god for that.

It did look like some alien had climbed under the bonnet tho, green goo everywhere!

I think point 3 is pretty important, in a lot of ways a high pressure cap shouldnt be required if the rest of the colling system is working ok ;)

I don't agree with that. Of course the cap will still be on the top of the tank. For it to come off, the metal of the cap would have to bend, or the plastic break, or the thing would somehow have to twist itself off. I'm sure when the tank blew your cap was in the 'open' position and was diverting coolant to your overflow tank as rapidly as the tiny overflow tube would allow it to (unless it was broken and stuck shut, but in my experience when broken the just leak, or open at lower pressure, from a worn spring). What happend was the pressure in the radiator was too great to be vented through the small overflow nozzle/tube, hence the top tank speperated from the rad. I honestly don't think that a stock rad cap would have made one iota of difference.

Bummer about being strandard though. Also, when the tank blew off did it just break a few of the little tabs on the core and then free itslef from the rest, or did heaps of them break off (or none)?

Richard

mmmmgtir, it severed thru the plastic tank itself not detached at the join. It may be possible that the cap had opened and simply couldn't release the pressure quick enough. Any way, now i have a beautiful 3 core copper radiator out of a racing GTR for $500. I think my overheating problems have been solved.

About 30mins of driving after putting on my 'High pressure' Nismo radiator cap I blew the top piece of the radiator apart. 2 days later it blew a coolant hose at the back of the engine. All fine now..but was a little paranoid about putting the nismo one back on :P

mmmmgtir, it severed thru the plastic tank itself not detached at the join. It may be possible that the cap had opened and simply couldn't release the pressure quick enough. Any way, now i have a beautiful 3 core copper radiator out of a racing GTR for $500. I think my overheating problems have been solved.

ahhh, yeah I've had a top tank start to crack and leak at that point too (with a stock cap installed). Just above where it has the lugs to sit on the core. They get hot and crack over time. After reading gtr032s post i'm now wondering again about the whole cap thing. I have a cusco .9bar cap on my gti-r and when it get's hot enough I've seen it open and bleed of pressure to the overflow tank. I know of dozens of people using various brand .9bar caps on otherwise stock systems. Was your cap rated to hold a higher pressure than that? Eitherway, sounds like your problems are solved now. :D

Richard

I think it had more to do with the age of the plastic on the top tank.

I had my top tank literally become brittle and crushed with the slightest overtighten of a hose clamp.

Old plastic goes brittle. Especially with the type of heat the top tank see's.

I would say it was leaking fluid, temp got high pressure builds more then the brittle top tank simply let go.

I replaced mine including labour and a coolant fill for $90 from Natrad.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Order for the 2025 model R35 GT-R were accepted from 3rd March and 26th August the last order rolled off the production line at the Tochigi plant. Concerning the R35 GT-R replacement, current Nissan CEO Ivan Espinosa said "Nothing has been decided about the GT-R at this time, but we are well aware that everyone is waiting. The GT-R will evolve and reappear in the future. Please be patient until that day comes." Nissan has a lot of issues with management and finances so take Espinosa's words with a big grain of salt. From what discussions I've had and read about here in Japan, not a lot of people are confident about Nissan's future, let alone the next GT-R. 
    • Thanks. We getting some parts along too so he will be solving the speed issue like next week so i will let you know what he came up with.   
    • 21 is explicitly the coils detected as the issue. Is it guaranteed the actual issue? No. Just the ECU thinks it is. When you say rattling, describe it better, get an audio clip as best you can if possible.
    • Yea got me coppers. Bad news is I just put them in and the car still has the light and shakes. I also noticed I hear like rattling coming from the exhaust piping right under me. Does 21 also have a possibility of being O2 sensors?   So, coil packs are good, the harness is good, the MAF is working, and obviously the spark plugs just replaced and working.
    • Make sure you drop the GTT base tune back in, and set your injectors again, this will remove anything playing up with it you may have removed. Possibly lean there as it's normally a fast transient going THROUGH atmospheric pressure, and a turbo motor would then quickly go richer as boost builds. The only worry you MIGHT have is ignition timing, as the DE is higher compression than the DET from memory. But again, you're not in boost, so the DE motor will be a lot more forgiving at atmospheric.   Get Murray, Kinkstahs, and Johnny's input on tuning haltechs, those guys have played with tuning enough in the past to be able to help now you're past the trouble shooting stage of the MAP issue
×
×
  • Create New...