Jump to content
SAU Community

Recommended Posts

Well they do say the best gift to give is one you would like to receive yourself. :D

You will need the plumber buddy.^

It aint hard Shell - just take up to an hour to do the lot.

$20 bucks max if you DIY.

Richard, I never knew you cared. What does a plumber charge to change an Oh Ring? LOL

Shell, yep it's not difficult as long as you can turn off the water, have a good sized shifter and the correct washers but mixer taps can be tricky.

Richard, I never knew you cared. What does a plumber charge to change an Oh Ring? LOL

Shell, yep it's not difficult as long as you can turn off the water, have a good sized shifter and the correct washers but mixer taps can be tricky.

haha snap... yep the water is the issue. No mixer taps.

Yeah, apartments may not have an easily accessible water switcherofferer. Might be central not individual.

If you rent, I'd be at least be contacting the Landlord if in doubt.

Look for a small panel or door in one of the walls,

Its probly in the laundry, or hidden in a cupboard or wardrobe,

There will be a tap, you may have to look around with a torch inside the wall to find it.

Or if it has an underground carpark they may be on the ceiling down there.

I have most plumbing tools, includung the tap reseater you will want for this job.

Ps spend the extra 5c per washer and get the good ones

Edited by D.I.Y. Mik

And...

Leave the taps open when you turn the water on to flush out the brass shavings,

closing the tap on shavings just puts a groove in the washer and they leak.

Hydroseal is a good lube for them, and you may need to seal the thread again with teflon tape or Lockseal.

Leaking spindles need replacing, they are cheap and its easier than refitting o-rings etc.

dads rule!

Edited by D.I.Y. Mik

thats sick! i have a lazy mans 4 foot with just your average tropical fish lol. my dad has an 8 foot in wall salt talk with clown fish and shiz. but im way too lazy to put that much effort in

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...