Jump to content
SAU Community

Recommended Posts

Well they do say the best gift to give is one you would like to receive yourself. :D

You will need the plumber buddy.^

It aint hard Shell - just take up to an hour to do the lot.

$20 bucks max if you DIY.

Richard, I never knew you cared. What does a plumber charge to change an Oh Ring? LOL

Shell, yep it's not difficult as long as you can turn off the water, have a good sized shifter and the correct washers but mixer taps can be tricky.

Richard, I never knew you cared. What does a plumber charge to change an Oh Ring? LOL

Shell, yep it's not difficult as long as you can turn off the water, have a good sized shifter and the correct washers but mixer taps can be tricky.

haha snap... yep the water is the issue. No mixer taps.

Yeah, apartments may not have an easily accessible water switcherofferer. Might be central not individual.

If you rent, I'd be at least be contacting the Landlord if in doubt.

Look for a small panel or door in one of the walls,

Its probly in the laundry, or hidden in a cupboard or wardrobe,

There will be a tap, you may have to look around with a torch inside the wall to find it.

Or if it has an underground carpark they may be on the ceiling down there.

I have most plumbing tools, includung the tap reseater you will want for this job.

Ps spend the extra 5c per washer and get the good ones

Edited by D.I.Y. Mik

And...

Leave the taps open when you turn the water on to flush out the brass shavings,

closing the tap on shavings just puts a groove in the washer and they leak.

Hydroseal is a good lube for them, and you may need to seal the thread again with teflon tape or Lockseal.

Leaking spindles need replacing, they are cheap and its easier than refitting o-rings etc.

dads rule!

Edited by D.I.Y. Mik

thats sick! i have a lazy mans 4 foot with just your average tropical fish lol. my dad has an 8 foot in wall salt talk with clown fish and shiz. but im way too lazy to put that much effort in

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...