Jump to content
SAU Community

Recommended Posts

FOR SALE

Freshly rebuilt RB30 bottom end for RB25 head.

- JE flat top forgies 8.3-1

- Shotpeened and polished conrods with ARP SR20 rod bolts

- Nirtraded Crank

- Modified RB30 Oil Pump

- Brass Sealing Rings

- Timing belt for Rb25/30 combo

- extra tension pulley for timing belt

- all new ring and bearings

Would be a straight swap from 25 block to 30 block.

This engine has just been completely stripped and rebuilt the other week. I bought a car with this engine and never got to actually drive it under boost, pulled off head to have rebuilt, so took opportunity to take engine out and have rebuilt as a safe option . The engine had done 9000klm's before rebuild only 1000k's with myself and that was the drive back from sydney

Cost $1100 for rebuild.

$3000ono

RB25de Head

Only recently stripped and rebuilt , still wrapped and unused.

Reciept states:

dismantle clean and inspect

pressure check

crack tested

face valves

reclaim vavle seats

remove and refit gallery plugs

helicoil threads

surface head

assemble head

dismantle and clean lifters

$800ono

large TO4e Turbo - rebuilt and never boosted, but driven off boost for short period.

.70 in and 1.33 ex housing, rebuilt by MTQ

Custom top mounted manifold - RB 25 head

XTR 52mm wastegate

braided oil and water lines for RB 30 bottom end

wish to sell altogether

$2900 ono

Rb25de manifold with runners and throttle body

$150

Surge Tank

$80

More to be added soon.

I will send interstate

if genuinely interested and would like photos leave your email and i will send them within the next couple of days.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...