Jump to content
SAU Community

Recommended Posts

Well just picked up from the latest tune getting there but not yet still getting hot at the moment guess i need to get that new radiator and still recons exhaust is restrictive but I like it the way it is so this is gonna have to do for now still its not to bad check out the graphs and opions welcome .Graphs show both high and low boost

Cheers Peter

lol.

I came across one of 'those' people the other day at Sprint Autoparts.

He was dribbling on how he had this R32 GTS-T.

166rwkw on 12.5psi, malpassi fuel reg, std ecu, exhaust, fmic.

He said he ran a 12.8 at 110mph with a 60ft of ~2.2. lol

He said if he got the launch sorted he would be close to the 11's. HAHAHA

What a knob head. Seriously, so full of him self.

ADPSI, which holds the current highest out put for an rb20 in aus, will be back out on the road soon, with even more power now. Its made 500+rwhp previously.

My 20 cents worth, it's not an RB20 if it has an RB26 crank, 3.5mm oversize pistons and RB26 rods. That's an RB24:cheers:

Legend01  besides shim clearances did you have any problems ?  no spring binding etc

i have a pair ready to roll

cheers

Hi MrMayhem

Being hydrolic there was no problem with shim clearences had the head done port and polish new standard valve springs and the cams just bolted straight in no problems with clearences with the lobs touching the head all lobs cleared fine though i must state that the hks cams 264 duration 9.0mm lift im using are heal and toe which means the take a little of the heal of the cam and add a little to the toe to get the lift required and had no trouble that im aware of with valve springs binding but only been reving it to 7500 rpm

Cheers Peter

Hi MrMayhem

                Being hydrolic there was no problem with shim clearences had the head done port and polish new standard valve springs and the cams just bolted straight in no problems with clearences with the lobs touching the head all lobs cleared fine though i must state that the hks cams 264 duration 9.0mm lift  im using are heal and toe which means the take a little of the heal of the cam and add a little to the toe to get the lift required and had no trouble that im aware of with valve springs binding but only been reving it to 7500 rpm

                                                          Cheers Peter

Gday peter - spring binding doesnt depend on RPM - if springs dont biond when you spin then engine over by hand, it wont bing at 9k rpm

cheers,

Matt

got my car dynoed today

190.7rwkw @14psi

has run 13.6 on 12psi 102.4mph

have had a max of 104mph

next mods:

suspension

ex cam gear

chip ecu

im not aiming at any great figures, instead a great road car with plenty of response.

RB20 forever!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
    • Sounds good, we will aim to be there! @The Bogan I'll give you a shout if you are heading up to campbelltown for the meet too.
    • Before I get to the test day, just to finish off the android head unit. This is a demo from car start up....the standard/host system takes a few seconds to boot (same as all v37) but Android comes up quickly. In this vid I'm using the delivered launcher but have set the default to Agami since which is easier to navigate when if use primarily 5 apps. You can see the host system still takes over when required eg putting it in reverse, and you can switch between Android and not by holding the back button 3 sec. It is pretty responsive (fast) but you can see I had to press harder than expected a couple of times.  I still have the phone connected to the stock system, and that also seamlessly takes over Android music playing. v37-android-demo.mp4 The bigger reason that I put this in though is so that I can use Ecutek directly on the head unit. That gives me a dash with logging (up to 20MB only), high and low value warnings on any parameter etc etc. I've run a USB cable from the Ecutek OBD dongle to a USB input on the unit, easy. v37-ecutek-demo.mp4   The unit did freeze on the launcher the other day, I think Agami was trying to verify the license when it didn't have a data connection...will monitor and report back if there are any other problems but so far I'm very happy with the upgrade.
    • Nah that is just crappy GPS mapping, I did have a small excursion (cold tyres, damp track, surprise!), will post up that when I get a chance.
    • So 10/10 times that code is coil packs? I mean if that's the case ill drop the $400USD or so to replace them. I didn't know these cars threw codes before the issue became an issue.
×
×
  • Create New...