Jump to content
SAU Community

Recommended Posts

LOL...a few ppl were looking very hard at my engine on the weekend as a few of the guys know the gear i have laying around and the car had been at the mechanics for a few weeks. So there was some suspicion that it was still my RB20. I think the fact that i left the bonnet restraint on and i didnt lift the bonnet all day also had a few ppl curious.

Why would you spend all that money putting in an RB25 to make 200rwkws max. When for less money you can bolt on a nice turbo and keep the big brother honest :)

gallery_462_50_59282.jpg

And it has been reliable. I would like to see how a full 2835 setup would go an RB20. GT30R seem to work well as well, but you are perhaps throwing away a bit too much 3,500-4,500 power to make the big top end. Still those that have done it are still quicker then me over the qtr so...GT30R obviously works as well :)

Yeh...just a few more hours to get the most out of it. Worth every cent.

Witness...RB20GOODNESS!!!!!!!!!!!!!!!!!!!

Clicky_Right Save As . approx 40meg of RB20 running around Phillip Island

So if mine can hang together after plenty of track work...the average street driven RB20 will be quite at home punching out good numbers

If i go out on the track with less then a qtr of a tank it gets fuel surge. As long as its above its ok. Couldnt be stuffed with a surge tank. its just more lines in the boot that can be knocked/damaged by stuff thrown back there.

The car is still my daily driver so dont want to lose the practicality of the boost. Some of the jap GTR pumps have a in tank baffle that i may look into if i ever need more flow then the 040 can provide (Highly doubt i will need bigger, i think it flows something like 235L/min?)

Yeh...just a few more hours to get the most out of it. Worth every cent.

Witness...RB20GOODNESS!!!!!!!!!!!!!!!!!!!

Clicky_Right Save As . approx 40meg of RB20 running around Phillip Island

So if mine can hang together after plenty of track work...the average street driven RB20 will be quite at home punching out good numbers

Great vid Troy!

the thing with the average RB20 its that they need a good tune (like yours) there's been plenty fail at only 200rwkw due to crap tune/detonation....

IMO - its all in the tune :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...