Jump to content
SAU Community

Recommended Posts

Cars aren't meant to be idled for long periods. I just drive mine straight off but limit revs to below 2.5k and only small throttle openings for atleast a few minutes. Wait about 5 mins till you start going much harder than that. I usually let it idle for about 1 min after a trip. But most of the time I take it easy at the end of the trip (coast in neutral down hill or driving quietly through car park) so may not even idle it.

Some say it warms up quicker if you drive it softly for a while rather than idling which can be of benefit, without thrashing it of course..

benl knows the score. everyone has their own thoughts on the matter but i reckon maybe 20 - 30 seconds just to let the oil move around a little then drive off but keeping revs really low and no boost till the oil gauge starts to drop a bit

Well obviously it takes a little time for sufficient oil to reach the top of the engine (Cams etc)

I leave mine untill the revs are in the 800 range then drive it easy till the temp needle is at operating temperature. So probably idle for around 3min.

Sometimes ill idle longer but theres nothing wrong with that, idle is idle, its certainly not bad for your engine :cheers:

yeh i idle untill the revs drop below 1G... u can hear it.

takes prolly around 3-4 mins??

thenew neightbour next door came and complained last week when I was leaving for work telling me to turn it off... wtf

They covered this in a magazine a month or two back. They said that because the block is cast iron and the head is alloy the metals have different thermal properties. They are designed to be at tollereance when hot. So the recommended procedure was to do light driving to warm it up as this was quicker and caused less damage.

and you can't tell an engine is warm by looking at the coolant guage. What you really need to knowis when the oil is warm.

Wasy to spot in a skyline because the oil pressure gets heaps lower once it is warm. When the oil pressure is normal (low) at idle its ready to give it some :cheers:

I previously used to let my engine warm up until the idle drops from fast idle.

Since the new engine build with forged pistons the builder said it is best to drive it gently straight off, don't idle it around when cold too long as it takes way to long to warm up and essentially will do more damage.

Basically idle it for the amount of time it takes to put your seat belt , put the stereo's face on etc..

Short shift and the car will come up to operating temp within 2km's, providing the thermostat is working correctly.

Then drive it normally but wait around 7-10 minutes until you give it a bootfull as that is roughly the time it takes for the oil temp to come up to operating temp and lube properly.

If I sit and idle the car I can still hear a slight piston slap after 10minutes of idle.

Drive the car and the piston slap disappears after the first 1-2km's.

Its only a real real mild piston slap that you would mistake for a slight bit of top end noise.

Any piston slap is slight scuffing piston slap so I would prefer to keep it to a minimum.

interesting posts, i often like to let it sit and idle a few minutes when possible, but i do know that the engine definitly warms up faster when driving it gently compared to sitting idle. It only makes sense that the oil will start protecting best once its in its operating temp, so the method which gets it there fastest is the thing to do. I think i wont be idling it to warm it up anymore, just drive straight off!

as far as getting heat into everything else is concerned, i wonder how critical this actually is? as anyone whos been to the strip on a busy day will know that huge waits between runs will have you launching and running a pass on a pretty much cold driveline!

there was a long thread a while back about this. what i remember and too heed to was that the car is not ment to be left at idle for long periods because "glazing" of the engine might occur. ive stopped warmming up my car in the mornings now and like others just take it easy till the oil guage warms up.

I love whenever there is a thread or discussion about warming up an engine that everyone seems to think idling is bad for your engine :)

All i have to say is you want oil on moving parts before you put load on them :(

Theres no right or wrong way to do it, idle for a bit, then drive. Its that easy :(

Thank god for long gone are the days of carby's and cold mornings.. :(

My injectors have just started playing up big time.

Massive hessitations on a free rev from idle. :)

It is very very noticable when cold, smoothing out when warm.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...