Jump to content
SAU Community

Recommended Posts

This will be useful if you need to replace your side mirrors, say if the glass gets smashed, or if you are doing your own compliance and need to change to flat from concave...

Its fairly simple and should only take 10 mins anyhow, but saves you having to think about it :)

First of all get the whole mirror assembly off the car. You may not have to actually, but it makes the process much easier. To do this you'll have to remove the door trim (remove pull handle screws, remove all screws around base and sides, pop off trim popouts, slide up).. After that if you have the plastic sheeting over the door wiring still in place, you'll have to carefully peel that back.

You should see where the mirror plug comes into the door and goes to the switch. Carefully remove the plug. There are 3 x 10mm bolts that hold the mirror to the door. Undo these, making sure to hold the mirror whilst doing it, so you don't drop it.

Now you should have it off... take it somewhere to a nice workbench, in front of tv, etc :) Look underneath the actual mirror part, and you should see a single screw. Thankfully Nissan has made it nice and easy to just get to the glass. Undo this screw, and you should be able to pull the actual part that adjusts the mirror the different angles.

Now that you can pull that out slightly, you should see the extra white plug that allows you to get this part out. Carefully press on the plug, and it should come off, allowing you to remove it from the main surround

Now you should have the actual glass part, and the backing plate separate. Flip it over, and you should see about 5 clips holding a sub bracket, which sits inside the actual glass holding bit. Use a long flat head screwdriver, and gradually prize it off, applying only a bit of force. Do this for each side and eventually this part will come off.

So now you should just have the mirror in the rubber grip which holds in place.. but you still need to get to the glass out by itself.

This probably best to do on a warmer day, or get out the g/f's hairdryer and use it to heat the back - as you will find there is some sticky chewing gum type adhesive on the back of the glass.

You should now be able to see the back of the glass so again, using the flathead, very carefully apply pressure to the glass. I found it easiest to apply pressure to different sides equally, and eventually it will slip out, maybe twisting the rubber a bit to help it on its way.

Bingo! You should now just have the mirrored glass on its own as one piece. Take it down to your local glass cutter and get them to cut out the same sized piece of glass.. and replace everything in the reverse process of removal!

All done. Easy as you like.. :headspin:

Link to comment
https://www.sau.com.au/forums/topic/59085-r32-replacing-side-mirror-glass/
Share on other sites

I think its only about $30 or something like that to get it cut. Just take it to an industrial glass or mirrors place (it will be listed in the yellowpages). Haven't actually done that yet :P When I found out how much it costs, I'll post it here.

Well its just mirrored glass.. the same sort of stuff your wall mirror, vanity mirror, etc is made of.

Well done tutorial

When I did mine I didnt take the whole mirror out

One screw directly under the mirror and the the whole lot pops out.

undo the connectors and its out.

Just remember to take the backing plate to the glaziers as well, as mine needed grinding back for clearance.(they didnt have mirror the same thickness)

  • 3 weeks later...

update: just got the glass replaced today..

Only cost $15 from a glass place up here. As the stock stuff is thinner that what you'll usually find around, they may have to use the thicker 3mm stuff - but that will fit.

Yes, as Just says, you will probably need to take the backing plate so they can fit it in properly. For the $15 and they bonded it in there and everything.

  • 2 months later...

Even easier way,

There is a screw under each mirror that releases the electric motor to move the mirrors once this is release the mirror just pops out, and then get a screw driver and pop it out from its mounting points..

All good and takes 60 seconds.

My car is R32 GTS-t

  • Like 1
  • 5 years later...

Guys,

Just putting it out there, especially if you have a level of intellect not so dissimilar to myself... :wub:

If you undo that single screw that sits under the mirror and locks in the mounting plate, the spring is compressed by the screw.

In laymens terms, it goes: Mounting plate > white half bulb, flat side facing you > spring, screw.

I know, laugh all you like - but it had me stumped hahaha.

Cheers,

Steve.

  • 5 months later...

R33 is the same. The trick is you have get the mirror off [out of the mold it sits in] to see the screw. If the mirror is broken then you have no problem but if you are like me and only trying to remount the mirror because the last person who did it made a botch of it then you have to heat the mirror up - this softens the adhesive that is holding it on and then you can carefully pry the glass away without breaking it.

I cleaned mine up, a final wipe with Metho, reafixed the mold to the housing with the screw and then used some windscreen silastic and set the mirror back into the mold.

But I wouldn't have known how without Predators tutorial....thanks for that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...