Jump to content
SAU Community

Recommended Posts

  • Replies 300
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

mine made the noise ALOT more after i installed my front mount. i also have a APEXi dual chamber BOV and didn't adjust it for the first run after that and it sounded really good but i wouldn't leave it like that.. you'll kill the turbo.

you think about it, the turbo is spinning one way then when you get off the gas all this air has to go somewhere. that place is back through the turbo which is spinning the other way.. thats when you hear the chop noise.

Peformance wise, wouldnt it be better to have a complete plumback system wired to flow back just after the airpod? By doing that wouldn't it reduce turbo lag?

Thats an interesting question. Although, it does sound logical......

Has a plumback system been designed this way? Or anybody using this setup?

Steve.

Yes thats right.

My car came with the factory valves blocked and it was SHIT.

It fluttered and was laggy.

So I had the plumback reinstated and now it works BETTA.

I can't believe that you care about

some poxy sound resulting from a flawed setup, rather than

having you car working properly.

Why don't you make a recording of it and just play it on your stereo?

Or is it for everyone else to hear.

as some were asking before, you need an aftermarket air filter to HEAR the flutter because it has less restriction. you may even have the same flutter with the stock air box, but you just cant hear it. but the sound does come from compressor surge.

r33zilla : you will NOT get flutter with a HKS ssqv, believe me i've been there done that. the ssqv was designed to elimnate EVERY possible effect of compressor surge and flutter, its just the way its engineered and designed. you will only achieve the faintest flutter, which you will barely even hear.

hope that helps

if u have a stock bov, and an air filter with a large surface area such as an HKS or TRUST one u will get little flutter.. But if u got an after market BOV running stock boost and u got an air filter it will flutter pretty loud... The reason y u dont need to remove ur aftermarket BOV is cause the spring inside it is really tight and only releases when ur on high boost (8-12psi or whatever).. The Stock BOV has a very soft spring... Once u get an airfilter ur car should flutter at low revs, but once u get above 5000 rpm, it will go tshhhhhh the normal sound which is normal.. I had a stock R33 and did that and got alot of flutter.. When i put my front mount on it was even louder, and when i changed the piping to stainless steel igot even louder lol!!! It is pretty mad, but be careful with what air filter u buy cause some dont filter as good as others.. But if u just want the sound, defenitely buy a HKS mushroom or a TRUST Arinx one for abt 100 bucks second hand they always for sale.. And changing the stock air filter to the pod is very simple, shouldnt take more than 40 minutes if u got the right tools..

hope that helped..

Rob

ahaha this question plagues every forum.

To enhance your 'Flutter'

you will need a AfterMarket POD Filter.

an AfterMarket Intercooler will help amplify the sound

Different sized turbos will also depend on how loud, how deep, how high pitched

The big thing, is having steel piping from the turbo to the pod filter. Usually its plastic from the factory and people rarely change it as its not really necessary... but changing this pipe to a steel one, will help amplify the sound.

People will argue to death that it kills turbos and whatever, and its more laggy all kinds of stuff... and really, its horses for courses - whatever you prefer.

I had a bov on my vl turbo, the spring in it died and the bov was useless (could not hold more than 7psi boost and would open up sounding like an external wastegate but losing all horsepower), that sucked... it was a TurboSmart Type III. after that i just took it off and had the hole welded up.

I had a bov on my R32, and it wasnt placed properly (it was not hidden)... stuck out like dogs balls, and as soon as a cop pops your bonnet, they think its christmas when they see it, because they dont know fcuk all about cars, but they know what bovs look like and they know it shouldnt be there...

I remember i told a cop it was standard, argued the point and got away with it. But i removed it anyway.

Bloody posers.

It's full sick.

I have a s15 stock re-circ. If take your foot off the accell quick enough when on full boost you still hear crazy woosh for some reason (I thought that wasn't meant to happen with a re-circ)... this thread makes me worry now maybe it's not up to the job but I'm only running .8 bar or so. :confused:

I still don't understand why people want these noises - just get a bigger turbo and make noise with the wastegate :(

This thread is gay.

The "flutter" sound (not to be confused with the sound from a sequetial BOV) is compressor surge, it happens when the compressor is operating severly out of its efficiency range, it is not a good thing.

So when I hear a car drive past fluttering between gears, I dont think "fully sick man", I think "that car is set up like shit, and that tool thinks it is great"

If you want it to be louder,

1)block up the BOV (causes the compressor to operate at essentially zero flow when changing gears) ie; way out of its efficiency range,

2) get a pod filter - stock box is designed to muffle the sound,

3) FMIC - larger volume of compressed air for the compressor to work against (at zero flow) during gear changes.

All that should reault in a longer louder flutter to tell people your car is fu(ked.

Sorry if I have offended anyone.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
×
×
  • Create New...