Jump to content
SAU Community

Recommended Posts

G'day all,

Just did a gearbox oil change on my R33 GTS-t and I thought I'd share it with everyone.

My box was crunching into second gear for the first 4-5 changes first thing in the morning (it get really cold here), so I thought that the synco's in second were stuffed. As well as that there was a whining coming from the gearbox for the first 2-3 minutes of driving in the morning.

I changed the oil and what a difference !!!!!!

Cold gear changes are sweet now, and no whine for the first few minutes of driving.

I used Castrol VMX80 gearbox oil, the difference is great, smoother gear changes, and when normal (warm) driving the car seems quieter than before, even though I didn't think it was noisey before.

To do it is easy.

Do the following after a drive so the oil is hot (and will flow out better).

Use a trolley jack and jack up the drivers side of the car.

Use axle stands under the chassey to make it safe.

You'll see the drain plug on the gear box about 1/4 way from the back of the box. A 1/2 inch rachet fit's nicely into it. You'll also see the fill plug on the drivers side and it's the same size as the drain plug.

Make sure you loosen the fill plug before you drain the oil. You don't want to find out that you can't get the fill plug out after you've drained all your oil!!!!

Drain the oil. Put the drain plug back in and then remove the fill plug. I used a pump to get the oil into the fill plug as it's a tight fit.

The gearbox took close to 4lt of oil. Basically you fill the gearbox until oil comes out the fill hole. Make sure you have the car as close to level when you fill it. I know it hard if you have to jack one side of the car up.

Put the fill plug back in. Lower the car, and that's it.

Easy, and has fixed all my worries.

BTW: the VMX80 was about $29, and the little oil pump thing was $12.

J

Link to comment
https://www.sau.com.au/forums/topic/631-gearbox-oil-change/
Share on other sites

  • Replies 84
  • Created
  • Last Reply

Top Posters In This Topic

Guest MrLolly

hey jay, i recently did mine and my 93 model 33 has its fill plug on the passenger side

also, no need to buy a special oil pump, just get one of those little plastic pumps that are used for getting fuel out of a can and into the car, cost $6, all you need to do is shorten the collector hose so that it fits into your four litre bottle

rod

Link to comment
https://www.sau.com.au/forums/topic/631-gearbox-oil-change/#findComment-16654
Share on other sites

Hiya Guys....

I basically have the same problem as Jay95R33 ... that is for the first couple of changes after you start the car going from first into second .... second gear grinds.... then it stops after a couple of gos....

So my question is ( and feel free to make fun of me :P as I have only had my 95 R33 GTST about two weeks ) Does the skyline have a dipstick for the gearbox ( manual ) ???? I had a look but couldnt find one??? Or is it self contained or something??? Do I just go straight for the dumping of the oil????

Help! :confused:

Brett

Link to comment
https://www.sau.com.au/forums/topic/631-gearbox-oil-change/#findComment-17082
Share on other sites

G'day Brett,

Naaa, there isn't a dip stick for the manual box. It's a sealed unit (except for a small breather I think), so your only option is to drain the oil and put fresh stuff in.

You can top it up, but it's best to drain the old.

It really is straight forward. The hardest part was jacking up the car, and then pumping that little pump thing about a zillion times to get the 4 litres in her.

J

Link to comment
https://www.sau.com.au/forums/topic/631-gearbox-oil-change/#findComment-17086
Share on other sites

Thanks for that....

Another question.... where is the jack spot for the R33??? I ask because with all my bodykits I dont want to put pressure on something I shouldnt.... ( I had a commodore before and it was dead easy :P )..... I should also go back to the import dealer and ask for a jack as I dont think I got one with the car...

P. S All you Perth guys should put out a message when you organise another cruise .... I would love to be part of a HUGE skyline cruise.... that would be fun .... and a great chance to learn some stuff :)

Thanks Again

Brett

Link to comment
https://www.sau.com.au/forums/topic/631-gearbox-oil-change/#findComment-17091
Share on other sites

Cool,

You should be able to use the normal jack spots that are near the sil, your side skirt should stop a little bit before it so you can get your jack in there without causing damage.

Once up, put your axle stands under the chassic rails.

Yeah, go back and get a jack from your dealer, other than being stuck somewhere with a flat and no jack, I think you have to carry a jack by law (stupid hay), but if you get a cop that's had a really bad day he could get you for it.

J

Link to comment
https://www.sau.com.au/forums/topic/631-gearbox-oil-change/#findComment-17125
Share on other sites

yeah same with mine when its cold it wont go into 2nd or back to 1st or grinds... unless i pump the clutch in neutral a couple of times... could need oil change i guess? Also this could be unrelated but if i start the car up and its really cold, and reverse, once the clutch starts grabbing sometimes it will squeal very loudly, sounds like its slipping... doesnt happen once its warmed up, anyone know what this could be?

Chris

Link to comment
https://www.sau.com.au/forums/topic/631-gearbox-oil-change/#findComment-19055
Share on other sites

Hmmm, the squeeling - does it sound like a bearing squeeling? It could be your thrust bearing on the way out. Not sure.

As for the 1-2 crunching, yepp, that's what mine was doing and the oil change made it all sweet. It was getting bad enough for me to forget about 1st gear for the first few take off's (use second), but after the oil change it goes between first and second like a dream now.

J

Link to comment
https://www.sau.com.au/forums/topic/631-gearbox-oil-change/#findComment-19194
Share on other sites

Originally posted by MrLolly

also, no need to buy a special oil pump, just get one of those little plastic pumps that are used for getting fuel out of a can and into the car, cost $6, all you need to do is shorten the collector hose so that it fits into your four litre bottle

ohhh if i only knew that when i had to change the diff+gbox oil on my escort.. i was under the car with a 250ml sunscreen bottle squirting it in..

thankgod i have patience

Shaun

Link to comment
https://www.sau.com.au/forums/topic/631-gearbox-oil-change/#findComment-19196
Share on other sites

Originally posted by thejackal

how often should you change your gearbox oil?

Originally posted by skyzerr33

every 80,000 to 100,000 km's

So if within 11 thousand K's mines done this, is it because

I've been driving it way too hard? :) :burnout:

or was it just crap oil they put in when it was complied? :confused:

(my car has only done 50 thou)

Or is my box on it's way out? :bonk:

Link to comment
https://www.sau.com.au/forums/topic/631-gearbox-oil-change/#findComment-19229
Share on other sites

They all seem to do it (crunch that is).

I've changed my oil a few times since I bought it 2 years ago... I use the VMX80 stuff in my car too... Works a treat!

As Jay said, the hardest part is pumping the oil into your gearbox... Man your arm gets tired! :P

A lot of compliance places don't even change the gearbox/diff/brake fluids anyways, just to save a bit of cash... I know the place I took mine didn't. You'll be surprised how much of a difference an gearbox oil change can make!

matt

Link to comment
https://www.sau.com.au/forums/topic/631-gearbox-oil-change/#findComment-20512
Share on other sites

With the VMX80 bottles snout i found that a length of garden black hose fits perfectly.

I then held the bottle upside down with the hose attached near the bellhousing and it was pretty easy to fill up.

Well it was easy as I had a Pit to do it in so it may be a little harder laying under the car but still easier than a sunscreen bottle.. heheh

Link to comment
https://www.sau.com.au/forums/topic/631-gearbox-oil-change/#findComment-20714
Share on other sites

  • 1 year later...

jayson i had the redline shockproof in mine $25 a L mind u

and now i have the same stuff u have, and mine crunches slightly into 2nd when cold

the redline stuff was great... next time in gonna buy some again

also when i refilled it i poured it through where the gear lever goes... didnt seem to do anything wrong that way... makes life easier i fink

anyone got any probs wif the way i did it?

Link to comment
https://www.sau.com.au/forums/topic/631-gearbox-oil-change/#findComment-397056
Share on other sites

You will be suprised how much smoother Nulon G70 gear treatment makes the gearbox with a couple litres of VMX80.

Since I had a VL Commodore that are renowned for diff whines i've used G70. The diff would whine like fark so I slapped a tube of this stuff in and a few hundred km's later the whine was so quiet you had to have the radio off, windows closed and silence to hear the whine.

My old VS V8 5 Speed manual used to crunch a little when cold. I slapped G70 in there and the crunching when cold dissapeared.

Same with the Skyline Box.. grabby feeling when cold is now gone.

Link to comment
https://www.sau.com.au/forums/topic/631-gearbox-oil-change/#findComment-397170
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The attached document is fine. I just downloaded & opened it.
    • Hello, sorry for being late to join the discussion, but my clock just died on me.   Ive tried to look at Michaels digital clock repair.docx and it doesnt work maybe the file has expired.   Please let me know if you can re upload it or take some youtube videos to show us how to get the clock installed? thanks
    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
×
×
  • Create New...