Jump to content
SAU Community

Wheels, to change or not to change...

wilch

By wilch,
in New South Wales

 Share

Recommended Posts

wilch Grand Master

wilch

Posted
Posted

Stupidly I started looking at wheels...

Now I've always been a fan of dished wheels but have been without with my current ride, as she came with already big wheels and good rubber.

At the moment she's wearing 18x9's all around with 235/40 rubber.

What I'm looking at getting are 18x8.5 235/40 fronts, and 18x9.5 265/30 rears.

Also, I guess the wider rears would help with traction.

Anyway, this is what she looks like:

866_myCarSameWheels.jpg

and this is what she could look like:

829_MycarDifferentWheels.jpg

Help! What do you guys reckon?

wil..

Link to comment
https://www.sau.com.au/forums/topic/64191-wheels-to-change-or-not-to-change/
Share on other sites
Menthu_Rae Collaborator

Menthu_Rae

Posted
Posted

Do it! The 2nd pic looks awesome =)

Dont put this off you getting the rims, but as far as better traction - tyre compound/brand plays a more important role than small changes in width... obviously going from something heaps skinny like 6.5" to 9" is going to improve it heaps (actually it depends, because in the rain you have more water running over the surface... but that all comes down to the tyre design too) - adding an extra .5" for more traction, you may find going to a diff tyre brand would help more...

wilch Grand Master

wilch

Posted
  • Author
Posted

Currently have Pirelli P-Zero Rosso's on all 4 wheels.. Sticky, expensive rubber...

There might only be 0.5" in width on the wheel, but the tire sizes are different, 235 vs. 265.

The 235/40 foot print is alot smaller than the 265/30 foot print isn't it?

Menthu_Rae Collaborator

Menthu_Rae

Posted
Posted

Yeah, P-Zero's are good in the wet, and yes - there's a fair size difference in the tyre footprint, but I was just saying - if you're using cheap-ish tyres and want better traction, sometimes you can find a better improvement from going to different rubber than going up in rim width.

I wasn't saying anything against going up in the rim width at all - i was just highlighting that if you're after better traction it can be something (cheaper, sometimes) to consider.

EDIT: Obviously you understand that - so it's all sweet and my post was pretty much useless then :(

Anyway, the rims really do suit IMO - however some might say white/white has been done and done again - but don't let a "common" style put you off changing. All that matters is if you're happy with your cars looks .

wilch Grand Master

wilch

Posted
  • Author
Posted

hey yeah blitz, I noticed you changed your rims to 34 GTR ones. What made you change them?

I'm still undecided. I don't want bling.. I reckon the white with silver lip looks kinda racey. I also like the little bolt things. But yeah, $1900 for a mod that isn't really needed, but does make it look a lot better (to me anyway)... I dunno..

Don't bring, ecu, turbo etc into it... They're all coming.. ;) But still. Ah well. I'll figure it out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...