Jump to content
SAU Community

Recommended Posts

  • Replies 75
  • Created
  • Last Reply

Top Posters In This Topic

a 99 rex is a lot faster in a straight line than a r33, both being stock. the rex is faster both on the road and obviously can launch harder.

if you think a rex has a shit top end, then so does a gtst they both die off at high revs(turbos too small)

just as a sort of related example, a friend had a stock 01 rex(bug eyed shape, slower than 99) and he ran 14.0 @ 100mph, slipping the clutch on the start (not a redline dump)

a stock gtst isnt anywhere near as quick.

(and i have had 2 gtst's)

I recently finished this project:

CONVERSION:

2000 Forrester (stock)- 96 WRX Engine (Front cut) 12psi = 120KW at the wheels

The older WRX's still used the same turbo but they had larger compressor housings giving them better top end.

This forrester has nothing down low but when it winds up it'll walk past a stock WRX!

This said I think the newer model WRX would have a tough time keeping up with the lighter R33 with less top end in a street situation even the older pre 96 WRX's would be struggling.

Reality is, in two so evenly matched cars the biggest decider is driver :wassup:

Maxx, the modded rexys you ran can't of been very modded at all. 180 atw is easy to get from em and being lighter than you they will pull on you pretty easy.

The 96 rexys had a different turbo too, it had more top end than the 97 onward rexys.

The current model rexes (03-04-05)are actually the fastest (and heaviest) wrx's made so far.

99's are sposed to have 160 kw at the fly too, not 180ish (i think) like the 33gtst's have.

Maxx, the modded rexys you ran can't of been very modded at all. 180 atw is easy to get from em and being lighter than you they will pull on you pretty easy.

The 96 rexys had a different turbo too, it had more top end than the 97 onward rexys.

The current model rexes (03-04-05)are actually the fastest (and heaviest) wrx's made so far.

99's are sposed to have 160 kw at the fly too, not 180ish (i think) like the 33gtst's have.

stock 33's are around 150-160 (I think) :confused:

Hey peeps here my 2cents.. I had a go against a 98 model WRX my mods were FMIC 3in turbo back runing 11psi agint the WRX turbo back Carbon bonnet running 13psi (in controlled conditions.. both running in street tyres... first run i beat him by Half a bonnet second was pretty close too wasnt able to pull away neith was he.. maybe if i only haad 1/4 tank of petrol instead of full LOL

every lil bit helpsss haha

stop being narrow minded skyline owners.

rough numbers.

wrx = 1300kg with 160kw

r33 = 1350kg with 187kw

so power to weight is close but add 4wd and then measure them in a proper place (400m) and the skyline will lose.

no doubt.

and to make it fair, use the same year model for both. 96, 97 whatever.

stop being narrow minded skyline owners.

rough numbers.

wrx = 1300kg with 160kw

r33 = 1350kg with 187kw

so power to weight is close but add 4wd and then measure them in a proper place (400m) and the skyline will lose.

no doubt.

and to make it fair, use the same year model for both. 96, 97 whatever.

Yeah, the (goodness) ranking is something like this:

1. GTR

2. WRX

3. GTST

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...