Jump to content
SAU Community

  

65 members have voted

You do not have permission to vote in this poll, or see the poll results. Please sign in or register to vote in this poll.

Recommended Posts

  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

can you get a pic of the rear part of the engine bay like the back part of the rocker cover that is blocked by the crossover pipe

and also please check the colour of the plate on the air flow meter.. should be a bright pink colour.

this is a series II AFM... little things like this will identify this infamous 1.5 which is supposed to have a series II engine but series I everything else..

if its the wrong colour its a series I.

if its the right colour.. then its a possibility that it has been in a bad accident and the front end has been replaced... but as to why the interior is half half... cos its not a complete series I interior cos of the dash surround which is from a series II

i have seen heaps of 1995's with that steering wheel.. and no series II i have ever seen has had 1 airbag.

This car might even be a rebirth lol, check the Vin number and make sure everything checks out. Check the Build plate and make sure it is not engraved, if it is then its rebirthed. Judging from condition of the front of the car i would be even thiking that its a 1993.

Well you guys have all been a great help.. I will see what posts come up over the week between now and Friday when it gets a check done by Hyperdrive.

Looks like its a bits and pieces but Im not going to rule out buying it just yet, the vibration it has is a bit of a problem but if it costs under $500 to fix it then hey its worth the money.

Thanks guys, I kinda get the impression that its not a series II and is more like a 1.5

Well with any luck it will pass all its tests on friday and I will be at the next cruise so you can all have a look at it.

- Adam

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
×
×
  • Create New...