Jump to content
SAU Community

Recommended Posts

between 125 to 170 (didnt go faster then that) last night the ****ing car would shake badly from the front, as I have never ever had any probs at high speeds, (above 80)before some thing is baddly wrong what do you guys think.

Link to comment
https://www.sau.com.au/forums/topic/65489-bad-shakes-problem/
Share on other sites

mostly side to side but smoothed out at about 175, I have just had the disks machianed on the front so I am think they may be causing wobble, but at 0 to 100 its fine. It still handles well at low speed. NO break noise either, it was shaking so bad it was rattleing shit that doesnt ever rattle.

wheel allignment also have you replaced these rotors you said were to thin ???

I have not had wheel allignment yet, but will soon. Its all started after I took the rims off and the disks off. There are machiened rotors but they said that it was fine before they did the job then after told me that they are stuffed.

I'f you've got a steering wheel wobble, then you've most likely lost a weight. It could also be that it was previously balanced on the car to deal with a hub/rotor/tyre balance issue, and removing/refitting the wheel has put it out of balance.

could also be Tail shaft... as you have mentioned you have had you clutch done... tail shaft could be put off... some ar picky, and have to go a certain way on.. if you put them back on, 90deg diff then they tend to shake... yup yup.

wheels tight but will check them again shortly, no weights off wheels that i can see, me thinks the disks are slightly warpped after bad machening (wish I could spell) and only having a prob at high speed. will keep ppl posted as to what it may be.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Waaay ahead of ya....(evil laugh!!) Will show the fitment and spec details later when it isnt as rainy !
    • Thanks Dose.....    I appreciate it!!
    • I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
×
×
  • Create New...