Jump to content
SAU Community

Recommended Posts

well i installed a momo steering wheel but i don't like it anymore as i have to sit too far forward to hold the steering wheel properly. Took the momo off unscrew the main center bolt but somehow the boss kit won't come loose? keep pulling yanking it still won't come.. if anyone knows how to take the boss kit off please help me as in stuck :cheers:

cheers

Link to comment
https://www.sau.com.au/forums/topic/66640-help-please-cant-take-it-out/
Share on other sites

it may be stuck on a fair bit unfortunately.. try and lube it with WD40 in there.. and try jiggling back and forth with small motions.

Otherwise what I would be doing (and I often take the dodgy brutal approach) is to drop the steering column as far as possible, get a bar behind it to sit facing the front (this is for my last one, it had a sort of frame structure).. and bash behind using a hammer.. small taps might be enough.

Yes, there is a sticker in there usually that says "do not use force", it may damage your steering, etc. But it never has on the last car.

once u unscrew the centre bolt (dont unscrew completely, leave it sitting there, just wind back a few times), then re-attach your momo steering wheel.

then start yanking. leaving the centre bolt on will ensure that when you finally yank it off the steering wheel won't hit you in the face.

also spraying WD40 at the centre nut may help a bit. when yanking back the whole steering wheel just becareful not to hurt your back, i hurt my back a bit due to pulling back too hard, but maybe i'm just getting old...

Never met a steering wheel I couldn't remove by anything other than gentle side-to-side jiggling of the wheel.

The R32s have reach, as well as height, adjustment of the steering column - are the R33s the same?

Take off steering wheel..

Now, undo center bolt, or as suggested undo it until its nearly at the end of its thread so it prevents you knocking yourself out (unless that sounds fun to you).

Now put the steering wheel *back* onto the boss, putting back the screws that attach it so its as it was (just with the center nut loose)

Now using the wheel as a kind of puller itself just keep yanking it forward, jiggling it, etc - and eventually it should pop off.. once you've got it loose, take off the steering wheel again, remove center nut, remove boss, and away you go.

It went on, it has to come off!!

Have you put the wheel back onto the boss?

Grab the wheel at "quarter to three", now jiggle back and forth while pulling towards you. Otherwise, PM me where you are, I'll try and get around to help you.

Just had a thought - how are you "jiggling" the wheel? If it's like you're steering the car, then the wheel is never going to come off. You need to jiggle back and forth along the axis of the steering column, ie pull up on one edge and push down on the other, then reverse that, all the while generally pulling the wheel towards you.

Clear as mud? Good!

You need to undo the nut, but as the others said, leave the nut on a tad. Leave the steering wheel on with all hex bolts still connected to the boss kit.

Ball you hands up into fists and bash with the outer part of the steering wheel really quickly with both hands at 9 o'clock and 3 o'clock, making it vibrate. You need to loosen the bond between the spline of the column shaft and the boss kit.

Then go ahead and try and reef/wiggle the steering wheel off. This is an assured way of removing the steering wheel!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...