Jump to content
SAU Community

Recommended Posts

I'm no longer interested in the DFA for meantime Shan, I might get it later on in future though. And my friend is switching his order from the DFA to EBC. So the order (including my friends) is now:

3x Independant Electronic Boost Controller

3x Hand Controllers

3x Cables

  • Replies 218
  • Created
  • Last Reply

Top Posters In This Topic

does the HC have light? and no writing? if so then do what newkleer said. The trimpot is located near the 25 pin thing to the left its blue and white, turn clockwise about 45 degrees. If the hc has no light at all then i don't know.

i'll try that out shortly......also ..i checkd the soleniod and tht works with direct power.. but when i hook it up to the board as per instructions..nothing happens.. ive got my jumpers set to suit ..as its a normal open unit.

when i turn the ignition on .....the solinoid ..being normally open should shut with power going to it.... its not doing that at all.

but ..at the same time ..i should have power to the HC.....but again ..its not doing that at all... trying to find my multimeter at the moment to track down the weak link

Matt

i havent either, but wasnt expecting till early next week (given monday was public holiday, so sending out on sat would be like sending out on tues)

Finished my DFA today, did everyone wire the link between the crystal capaciter thing and the hole near the plug?

If you are talking about the 20Mhz crystal, yeah, I did. It's jsut to ground the metal case of the crystal but in all my years in electronics, I haven't yet found why they do this. I'd say do it anyway. :)

this one's for the guys waiting for a mail delivery... I've been sent back all the parcel post packages I sent out because I hadn't signed the dangerous good disclaimer :rolleyes:

anyways, after talking to the guy at my postoffice I've organised for them all to be delivered via express post (24 hour delivery) so you should all recieve your packages tomorrow for sure.

Hey guys ive just noticed something on the IEBC pcb thats a bit confusing, the small link link5 is shown in the wrong position on the printed circuit board... Make sure you follow the overlay diagram not the picture and not whats printed on the pcb.

And yeah i earthed the crystal things... i dont think thats documanted very well either, i suppose its not that important to do it.

hey funky jsut wondering if it's time to start the new group buy, or at least get peoples intrest.

awesome job mate

cheers mark

i'll start another thread for group buy #2 shortly... i've just sent off the last of the first batch (hehe good one NewKleer)

this thread's a bit too long for people to browse thru n stuff. But has lots of good reading for people buying... I'll summarise costs in the new one and you guys can put down what you want. Once the necessary numbers are up (which should be within a few days) I can put in a second order.

next time I'll just cut the crap and just mail out using 24 hour delivery satchels, they're much more effective and they can hold an ebc, dfa, cable, book and handcontroller... just.

Did everyone get fragile stickers on their packaging, because I asked the postie to stick em on.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Maybe also really stiffly sprung track cars. Get the inside wheel up in a corner and all the fun stops. Also me sometimes (rarely) when I have to stand on the brake to convince the diff to drive the wheel that is still on the ground when I'm trying to diagonally get over severe driveway entrance, etc.
    • I feel like I'm missing something. You had an authorised installer come out and install a new alarm. Post install the car doesn't start, and you aren't getting the installer back to fix what they did wrong?
    • So either way it is gearbox out and look what is wrong?  I know about the input shaft bearing. Even before swap/new clutch the it sounded exactly like this: So is that inout shaft bearing or the other was installed backwards?  And can some please tell me the part number for that input shaft bearing? The gearbox is small box from R34 N/A and number is FS5W71C. Thank you  
    • I am yet to see anyone ever regret a quaife or helical. ...other than drifting/skidpan duties. I kind of want to upgrade my factory helical with a Quaife (but really it's not ultimately that different, and is a MASSIVE UNDERTAKING), that's how good the hype is about them, that I want to try them 'just to see'  
    • D2 and Ksport are essentially the same thing and basically just generic Taiwanese manufacture. Better than ChinaBay crap, but... not top shelf. Öhlins have got to be some of the best dampers around, so likely to be a good option. It's going to get to the point though where I suggest you buy from Oz. We have at least 2x excellent options here. If I were you though, I'd be talking to KW about doing something for the R33. There's bugger all difference between that and the 32. In GTR land, anyway.
×
×
  • Create New...