Jump to content
SAU Community

Recommended Posts

I wrote this down a little while ago, have a read but maybe let some of the other more knowledgable forum users look over it and pick out anything I've missed, which is entirely possible.

DISCLAIMER: While i have performed this myself and believe the below to be correct i am NOT a mechanic, I'm a backyard tinkerer, you do it all at your own risk. Just take it slowly and be methodical, don't rush anything, but if you're not confident in your abilities resign yourself to paying a mechanic to do it for you.

1. Disconnect power to the injectors (pretty sure they're grouped in to 3's and there's 2 plugs power them just trace the wires back and unplug).

2. Pull the coil packs off the spark plugs, leave the coils on those 2 rails in groups of 3, just undo the rails and lift.

3. Check your spark plugs now if you haven't already.

If there's nothing obviously wrong with the plugs put them back in and move on.

4. Pull all the rubber boots off the 6 coil packs, be careful the spings don't fall out the end, it CAN happen.  

5. IMPORTANT! Use something to mark the position of Crank Angle Sensor (a blob of whiteout overlapping the CAS and timing cover works).

6. Undo the 3 bolts and pull the CAS off.

7. Rest the coil packs so they're tips are a short distance from, but NOT touching, the head or anywhere that's well earthed.

8. Turn the ignition to ON (don't try and start it!).

9. Take the CAS in your hand with the little "stick" facing you and rotate that stick ANTI-CLOCKWISE.

You should get sparks leaping from the tips of the coils to the rocker cover one by one over and over. If indiviual coils spark sometimes and not others make sure there's a clear and clean path for it to spark to and from and that you're not turning it clockwise as it sparks unpredicatbly when you do.

To put it all back in, turn off the ignition, and go in reverse taking care with CAS, manipulate the stick until it slots over and the whole thing slides on, don't force it, then line those marks you made back up otherwise your timing will be out. Plug the injectors back in etc etc.

once the car is warm, just diconnect em one at a time, reconnecting.

if te idle doenst change... then youve got a stuffec oil pack

he can't do this unfortunately as his car wont start!

but yeah, that is the easiest way to test these kind of problems.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
×
×
  • Create New...