Jump to content
SAU Community

Recommended Posts

I wrote this down a little while ago, have a read but maybe let some of the other more knowledgable forum users look over it and pick out anything I've missed, which is entirely possible.

DISCLAIMER: While i have performed this myself and believe the below to be correct i am NOT a mechanic, I'm a backyard tinkerer, you do it all at your own risk. Just take it slowly and be methodical, don't rush anything, but if you're not confident in your abilities resign yourself to paying a mechanic to do it for you.

1. Disconnect power to the injectors (pretty sure they're grouped in to 3's and there's 2 plugs power them just trace the wires back and unplug).

2. Pull the coil packs off the spark plugs, leave the coils on those 2 rails in groups of 3, just undo the rails and lift.

3. Check your spark plugs now if you haven't already.

If there's nothing obviously wrong with the plugs put them back in and move on.

4. Pull all the rubber boots off the 6 coil packs, be careful the spings don't fall out the end, it CAN happen.  

5. IMPORTANT! Use something to mark the position of Crank Angle Sensor (a blob of whiteout overlapping the CAS and timing cover works).

6. Undo the 3 bolts and pull the CAS off.

7. Rest the coil packs so they're tips are a short distance from, but NOT touching, the head or anywhere that's well earthed.

8. Turn the ignition to ON (don't try and start it!).

9. Take the CAS in your hand with the little "stick" facing you and rotate that stick ANTI-CLOCKWISE.

You should get sparks leaping from the tips of the coils to the rocker cover one by one over and over. If indiviual coils spark sometimes and not others make sure there's a clear and clean path for it to spark to and from and that you're not turning it clockwise as it sparks unpredicatbly when you do.

To put it all back in, turn off the ignition, and go in reverse taking care with CAS, manipulate the stick until it slots over and the whole thing slides on, don't force it, then line those marks you made back up otherwise your timing will be out. Plug the injectors back in etc etc.

once the car is warm, just diconnect em one at a time, reconnecting.

if te idle doenst change... then youve got a stuffec oil pack

he can't do this unfortunately as his car wont start!

but yeah, that is the easiest way to test these kind of problems.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...