Jump to content
SAU Community

Recommended Posts

Finally finished my rebuild after about 7 weeks.

Did

40 thou over rebore

Arias forgies

match ported everything

reseated valves

regasketted everything

New big end and thrust bearings

N1 oil pump

N1 turbs

S/S dumps and fronts

Os giken twin plate

Os giken adj cam gears

Gates radiator hoses

Gates timing belt

Clear cam gear cover

Acid bath

All welsh plugs changed

Oil cooler and filter relocator

Anyway I am still in run-in time and the car seems a bit less than it used to be..I know I might be jumping the gun as I can't really get up it yet. But I have been around 5500rpm ish at 0.7 bar of boost and my 33 was always the 'lesser' car power wise....Just chasing thoughts

Could it be because we opened the piping so much it will take more exhaust gas to boost?

Is the engine just so new and tight?

I am looking forward to giving it a proper boot full but I must behave for a few more hundred k's...

The next step is injectors,pump and fc in case you were wondering why they weren't on the list.

Link to comment
https://www.sau.com.au/forums/topic/69469-32-gtr-rebuild/
Share on other sites

could be the run in oil as well, i think mineral oil is harsher on the internals at high temp, but thats what it needs to bed the engine etc.

sweet build!! i have just done the exact same rebuild!!

i found that during the run in it also was abit down, but i got it tuned on the run in oil and it pulled 250rwkw on pits's dyno in 3rd at 1.2bar. It was running rich with the lower comp ratio

after the oil change it seems to be much smoother and rev's alot easier. i can feel the power earlier, and it feels like it may come on harder??

i will have it dynoed at the next dyno day & post the results. also pits's dyno results are usually at least 10% low??

Link to comment
https://www.sau.com.au/forums/topic/69469-32-gtr-rebuild/#findComment-1285363
Share on other sites

Guest two.06l
Finally finished my rebuild after about 7 weeks.

Did

40 thou over rebore

Arias forgies

match ported everything

reseated valves

regasketted everything

New big end and thrust bearings

N1 oil pump

N1 turbs

S/S dumps and fronts

Os giken twin plate

Os giken adj cam gears

Gates radiator hoses

Gates timing belt

Clear cam gear cover

Acid bath

All welsh plugs changed

Oil cooler and filter relocator

Anyway I am still in run-in time and the car seems a bit less than it used to be..I know I might be jumping the gun as I can't really get up it yet. But I have been around 5500rpm ish at 0.7 bar of boost and my 33 was always the 'lesser' car power wise....Just chasing thoughts

Could it be because we opened the piping so much it will take more exhaust gas to boost?

Is the engine just so new and tight?

I am looking forward to giving it a proper boot full but I must behave for a few more hundred k's...

The next step is injectors,pump and fc in case you were wondering why they weren't on the list.

did you open up the exhaust ports when doing the head??

Link to comment
https://www.sau.com.au/forums/topic/69469-32-gtr-rebuild/#findComment-1285463
Share on other sites

ricknismo

I have an R32 - and have just done the SAME rebuild, I'm also still runnin in (~1500klms on the dial so far) – I have R34 N1s with hks style non-turbulent dumps and a full 3.5” exhaust + the other stuff you mention

At 8psi - I'm gettin ~180awkw I'd say (I can keep up with a std WRX and VYSS)

B4 the rebuild I had about 210awkw – but my bottom end was shot (pots 4 and 6 totally rooted), no dumps, no port and polish blah blah blah

It does not rev out as smoothly as it did b4 - but it I'm not expecting things to fully loosen up until past 5000klms (at least) and I have lost the mineral oil

I have the PFC + Adj CAMS + 550cc injectors + Apexi EBC to install in the next week or so.

I'm expecting somewhere near 280awkw @ 1bar once this kit is installed and tuned

Link to comment
https://www.sau.com.au/forums/topic/69469-32-gtr-rebuild/#findComment-1285877
Share on other sites

  • 3 weeks later...

Had a play today...found a major boost leak.

Here's a trick...I clamped a plastic cup in the rubber hoses where the air filters go, shoved an air compressor up the (or any) air line and pressurized the whole system...found a couple of leaks...Might still have a little one though.

Link to comment
https://www.sau.com.au/forums/topic/69469-32-gtr-rebuild/#findComment-1316468
Share on other sites

  • 3 weeks later...

I found the problem...Yeah.

The standard boost solenoid has a T that goes to the plenum on the same line as the actuators...This won't work with an aftermarket boost controller and stuffs around with the sensors I guess. I ran a new vacuum line dedicated to the actators and it all good now.

Link to comment
https://www.sau.com.au/forums/topic/69469-32-gtr-rebuild/#findComment-1353301
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...