Jump to content
SAU Community

Recommended Posts

Guest Da_Man

I have a set of Brembo front and rear calipers and rota with pads for sale. A1 condition $2200ono price drop $1900

R33 GTR Driver and Passenger seats for sale $1600ono price drop $1500

RB25 head Ported, polished, and serviced $900ono SOLD

R33 GTSt s1 head lights A1 condition $600ono SOLD

Triple plate OS clutch A1 condition will fit R33 GTst $1800ono SOLD

Malpasi fuel reg $75

Link Ecu $750 price drop $700

Trust power extream 2 exhaust system for R33 $675 price drop $600

R33 s1 coils $150

R33 Gtst brake front and rear with rota and pads $750 Deposit Taken

R33 Gtst heater box $40

Standard RB25 cams In&Ex $100

R33 Gtst rocket covers $100 Deposit Taken

for more info call me on 0414 867 446.

***************No Time Wasters Please****************************

Link to comment
https://www.sau.com.au/forums/topic/69681-upgrade-parts-for-sale/
Share on other sites

hi just wondering if the seats are still available and if u could send us some pics to [email protected].

if not wat colour and condition are they in. pictures would be nice though. thanks

The heater box? Do you mean the heater core, that goes on the firewall under the dash behind all the climate control crap? If so then I want :)

Also, those seats are a little on the wrong side of "WTH?" $1600 for standard seats? Ive seen them at wreckers for $700 each, and set of aftermarket seats from Autobarn wont cost anywhere near that much.

Guest Da_Man
The heater box? Do you mean the heater core, that goes on the firewall under the dash behind all the climate control crap? If so then I want :cheers:

Also, those seats are a little on the wrong side of "WTH?" $1600 for standard seats? Ive seen them at wreckers for $700 each, and set of aftermarket seats from Autobarn wont cost anywhere near that much.

Yes heater box under dash.

Seats are sold at just jap (when they have them in) for $2K. But thanks for your input.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...