Jump to content
SAU Community

Recommended Posts

LOL...3240s, i dont know d1ck about engine building so shouldnt comment. :)

It sounds like a lot of fun...but with turbos that size i would have thought you would need more then mild port and polish, you would need really high lift, long duration cams...extensive headwork and the valvetrane set up to love 10,000rpm cause you wont be seeing 20psi until around 6,000-65000rpm i suspect...so are you still running std ratio gearbox. Anyway im sure you have looked into it and understand it all better then most of us sisnce you have already built the engine

LOL...sounds like awesome fun, and good work for having a go, but i think you will have some work to do making the whole package work. I suppose you can always sell those tasty turbos and go for something a little more sane like twin 2835s:)

Is it a drag car, dyno car...if its a dyno car then get it tuned up on some serious jungle juice and lets see what the beastie can do:)

  • Replies 88
  • Created
  • Last Reply

Top Posters In This Topic

i just got my new engine and very nice indeed what do people think how much power i would make at the rearwheels in a r33gtst put your info in and i give you the honest power figure? as it follows in mods

 

 

Rb26 stroked out to 2.8

hks crank  

hks rods

hks pistons  

N1 nismo cams  

hks valves and springs

mild port and polished head

hks cam gears  

n1 oil pump

n1 water pump  

1000 cc injectors

100 mm throtlebodie

pair of 3240 hks turbos

and running it with motec m800 ecu  

3 half in dump pipes into 3 inch nur spec r blitz sys

and nice new pair of fuel pumps and new fuel lines tobe put in  

and nismo fuel reg  

 

this it was ive got done and now have all built ?  

as im yet to put it in the car i just want peoples thoughts of what power im going to put out in the rear wheels

I find this hard to believe this is real

but if it is there are a few issue with the system

1000cc injector you going to need new fuel rail

N1 fuel regulator i would dont be up to the job

twin 3.5" into one 3" wtf (i run 3.5"single for 320hp turbos)

a twin 3" might get by

N1 cams (why oh why would you skip on cams)

N1 oil pump (you cant be seriously going to run a std flow pump with a 1200hp turbo set up)

and where is your cooling system

5" thick cooler

oil cooler

custom sumpcustom radiator

etc etc

cause if you don't you mos well go burn the money now

ive been talking to steve while hes been in japan... this aint a bullshit thread.. he is a very broke man. lol and is even cutting his holiday time back because he spent to much on little toys... wait and see and drool along with the rest of us. :cheers:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...