Jump to content
SAU Community

Recommended Posts

Hey guys,

This question might've been asked already...sorry about this but I need to know where GTR owners recommend their car to be tuned. I'd be casing a tuner with a 4wd dyno.

I've had my previous GTR's tuned at Croydon Autosports in the past and they do a great job but money is a real issue for me now and they can be expensive.

I was thinking about taking it to Autotech at Granville....

Link to comment
https://www.sau.com.au/forums/topic/71078-where-to-tune-a-gtr-in-nsw/
Share on other sites

  • Replies 106
  • Created
  • Last Reply

Top Posters In This Topic

Is it really worth saving a few dollars on a very expensive car and go with someone that not as well regarded or had nearly as much experience as Jim at CRD???

in the long run it will be cheaper to pay a little more up front, than have to worry about some back yard tune.... Rebuilding a Tough RB26 can cost big money, Trust me I Know!!!

I am not doubting Autotec's ability to tune a GTR, but i can guarantee that they wouldn't have tuned a third of the amount that Jim has... Experience is everything

I'm using Adam from JEM, I'm pretty sure if you speak to him he could hire a 4wd dyno as his is only 2wd

All he does is tune all day everyday no mechanical work so you'd be hard pressed to find someone with more experience

http://www.justenginemanagement.com/ I've always found 100% honest, fair and a great tuner which is about all you can ask for :rofl:

i had mine tuned at HITMAN. I thought he was pretty good. just like boofiveters tuner all Matt (hitman) does is tune. so he certainly knows his sh1t.

no 4wd dyno though, but i'm sure he could get to one.

I had mine tuned at two places(RUF PERFORMANCE and a mate who tuned a few cars before) before going to CRD

Jim done the best tune buy far,the car feels like it has a factory tune in it and he got more power out of it then the orthers did.

Im running a POWER FC,4 inch exhaust,cam gears,pods,everything else is stock (GTR R33 LM) and it makes 250klw at all the wheels,it ran flat 12s on street tyers at the creek 2 weeks ago dont waste your money go and see jim

I had my old 33 gtr tuned at bel and it ran 11.7 @121 mph @wsid on 18" street tyres . The only mods , full exhaust , power f/c and 1.2 bar boost , everything else stock , even stock airbox .

Ben knows his stuff and he has the jap software for power f/c's .

He doesn't have a dyno but he is moving very soon and then he will have a 4wd dyno .

When i finish my r34 it will be tuned by bel , thats for sure .

I would have to reccomend Advan Performance in Silverwater, they are the only one's who i trust with my car and they have made some very good and reliable power out of GTR's eg. one particular R32 GTR running a T78 426kw atw they only have a rwd dyno but they pull the front shaft on GTR's for tuning. they know GTR's inside out :D

I would have to reccomend Advan Performance in Silverwater, they are the only one's who i trust with my car and they have made some very good and reliable power out of GTR's eg. one particular R32 GTR running a T78 426kw atw they only have a rwd dyno but they pull the front shaft on GTR's for tuning. they know GTR's inside out  :D

They are good but you have to $$ if you want to go there to give you an idea , price of a install for a boost controller $1000 inc tune . My face after he told me ... priceless .

I had my old 33 gtr tuned at bel and it ran 11.7 @121 mph @wsid on 18" street tyres . The only mods , full exhaust , power f/c and 1.2 bar boost , everything else stock , even stock airbox .

Ben knows his stuff and he has the jap software for power f/c's .

He doesn't have a dyno but he is moving very soon and then he will have a 4wd dyno .

When i finish my r34 it will be tuned by bel , thats for sure .

so you're the GTR that ben talked about :wassup:

so you're the GTR that ben talked about  :wassup:

You can get dynos to read whatever you want them to , the proof is on the track .

we have another 33 that ben tuned it only makes 290 kw @ all 4 but it did run 11.33@ 124 mph , so there you go .

You can get dynos to read whatever you want them to , the proof is on the track .

we have another 33 that ben tuned it only makes 290 kw @ all 4 but it did run 11.33@ 124 mph , so there you go .

Exactly, Jerry. There is more to it than just max power. I bet you that 33 makes more average power than one with a higher peak power figure.

Exactly, Jerry. There is more to it than just max power. I bet you that 33 makes more average power than one with a higher peak power figure.

It does definatly come down to the area under the curve but that doesn't mean you can't have a relativley high peak power with good mid range etc too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...