Jump to content
SAU Community

Recommended Posts

Ok peeps ..... Pauls been on my case for a while now to get rid of these out of my garage because as you all know my baby is now sporting his hand me downs ..... so if anyone would like my hand me downs please get in contact with me.

4 x Roh 17" Adrenline Rims in reasonably good condition - theres a mark on the rear one - its not huge - otherwise they are like new. They are without tyres ..... well there's tyres on them but lets just say they arent much use to anybody and i'll get them stripped off before I hand them over ..... unless you want them.

Most people know what my car looks like on them - and unless you've had your head in the sand for the past 5 years you should be familiar with what these mags look like.

$650 ONO

Cheers

Lauren

Link to comment
https://www.sau.com.au/forums/topic/72203-fs-perth-only-roh-rims-17in/
Share on other sites

can u get racks for a line?

please say yes cos the boards are driving me maaaadddd!!!!

we looked everywhere but we can only find soft ones and they dont fit a two door unless its a hatch?

Yes you can.There was a thread about them a while ago. Search this forum for roof racks. I'm sure you find something :(

Now back to the topic please ;)

Interested, If no one snags them by tonight I'll chat with you or Mr Paul at the commitee meeting tonight. (yeah I know I need to get rid of my stockies)

mikey theres 2 sets of rims at garage gav that might interest you the ones on cherry red now and the ones on my avatar both sets need lil tlc

if i could get rid of one of these sets i might be interested niz

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
×
×
  • Create New...