Jump to content
SAU Community

Recommended Posts

Thinking of replacing my hiflowed turbo to a GT35/40R 0.70 / 1.06 internally wastegated turbo.

Has anyone else done this conversion and can you advise the handling ie lag, dyno results, drivability, when boost comes on etc.

Currently do drags and circuit in SII GTS-T with intercooler, Power FC, Hiflow injectors, Z32 airflow meter, fuel pump, fuel pressure reg etc. - acheiving 302hp in third gear dyno. Would really appreciate hearing from someone who has gone through the exercise - good or bad???

Cheers

Link to comment
https://www.sau.com.au/forums/topic/72642-gt3540r/
Share on other sites

I have been doing alot of research on this (haven't done it though) but in alot of cases, I wouldn't go for the 1.06ar exhaust housing, due to MASSIVE lag on a RB25.

I have a friend that has this turbo on his 95 supra (3.0l) and it hits full boost at 4200rpm. A guess at full boost on a rb25 would be 4500 - 5000rpm!!!

Thats way too much lag for me. I'm not an expert, but thats my opinion.

I hate lag, so I am going to eventually purchase something with a .63ar exhaust. If you are looking at big power, I'd go a .83ar exhaust.

Not sure on the Compressor size though..

SK might have an idea if he reads this thead.

Link to comment
https://www.sau.com.au/forums/topic/72642-gt3540r/#findComment-1340855
Share on other sites

over 5k IMO

its bigger than my GT30 (4200rpm/16psi) and then your going bigger again on the Exh housing.

get a .82 and it'll be much nicer. Id even say a GT30 like mine. Its awesome for all forms of use

Hi Nismoid,

Thanks for the feedback. I was trying to keep the internal waste gate due to simplicity, cost etc. but seem to be only able to get the thing in a a/r1.06 exhaust. comp is a/r 0.7. I'll do some research on the GT30. Can you tell me your dyno result atrw and qtr mile times...much appreciated

Link to comment
https://www.sau.com.au/forums/topic/72642-gt3540r/#findComment-1341407
Share on other sites

I have been doing alot of research on this (haven't done it though) but in alot of cases, I wouldn't go for the 1.06ar exhaust housing, due to MASSIVE lag on a RB25.

 

I have a friend that has this turbo on his 95 supra (3.0l) and it hits full boost at 4200rpm. A guess at full boost on a rb25 would be 4500 - 5000rpm!!!

 

Thats way too much lag for me. I'm not an expert, but thats my opinion.

 

I hate lag, so I am going to eventually purchase something with a .63ar exhaust. If you are looking at big power, I'd go a .83ar exhaust.

 

Not sure on the Compressor size though..

 

SK might have an idea if he reads this thead.

Thanks mafia,

I'm very concerned about lag as well... as I use the car on the circuit and need quick response as well as long legs in the straight. I want the best match for the engine capacity but am finding it very difficult to get a straight, independent answer...hence why I'd like to get feedback from anyone whose fitted an ungrade turbo and their actual results

Cheers

Link to comment
https://www.sau.com.au/forums/topic/72642-gt3540r/#findComment-1341420
Share on other sites

so far, the all hailed shootout mode

330rwkw with a hybrid mix of fuel, not just normal PULP on 24psi

made around 270rwkw without the fuel and 17psi

and the show is on well and truly around 4200rpm-4500rpm.

Best match is the GT30 for an RB25, if you want bigger power then a GT35 is the go but it comes at a cost, and mine is quite nice on the street

Im heading for some drag this friday so i'll have a rough time/mph then

Link to comment
https://www.sau.com.au/forums/topic/72642-gt3540r/#findComment-1341441
Share on other sites

Stealth,

Have you considered importing a HKS GT2835ProS (270-280rwkw) or HKS 3037ProS (300-320rwkw) from japland? They are both Internal gate. hence the PRO

Form memory they are around the 2.6k mark, unsure exactly the extra tax's and crap on top. I did look in to it a while back and have since forgot.

I 'think' stamp duty is only 3% on turbo's then you pay the GST. or is it the GST first then the stamp duty on that. :D

Link to comment
https://www.sau.com.au/forums/topic/72642-gt3540r/#findComment-1341453
Share on other sites

my mate and i have just finished a conversion in his vl. its an rb25 with a gt35r/1.06 rear.

the engine is standard except for tomei poncams,splitfire coils,xf throttle and fuel and computer obviously.

it is running through a vl turbo 5 spd.also a 3:45 diff ratio

the engine makes 20 psi by 4200rpm and is producing 313rwkw.

personally i would recommend the .84 rear housing and a 4:11 diff

Link to comment
https://www.sau.com.au/forums/topic/72642-gt3540r/#findComment-1341610
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Nah. Was just wondering if you were having a small stroke or if there was some slur/gaf/inside joke that I wasn't aware of.
    • That was a fark up, it's Salamanca Place I was thinking of. And now I'm curious as to what potential slur/gaf I have caused with Salamander Road, ha ha!
    • Actually everyone on the roads was really well behaved. The only person that did any minor tailgating was a local hoon in a Turbo Focus. Unfortunately we weren't going the same way so there was no grand initial D touge battle. Lots of people pulled over and let me through. The amount of "Hey man nice car, omg skyline, nice 34 man woo" was suprising. Like really suprising. Like almost annoying. My partner was obviously surprised, she'd never seen anyone in the real world point out the car/like the car/want to chat about the car before, so to have like 3 people per day mention it was notable, I could finally say SEE? SOMEONE THINKS THEY'RE COOL. Everyone was also pretty suprised about the weather. Every day was dry and about ~13-14C. Mount Wellington had a sign that said they close the gates at 9pm and I was heading up there at about ~7:30. It was VERY apparent that conditions were getting significantly worse by the minute on the way up and down. The road on the mountain was terrible though, it's no driving road. I have various suspension related questions now. Luckily it was only about 20 minutes from where we were staying to the top of the mountain as said Google maps. We only had the 2 nights in Hobart. We went to the Farm Gate Market though which was really good - And went down to the Hastings Thermal springs/caves down there during the day. I'd definitely be up for going back again, so luckily there's a few more sights yet to see. Didn't get to do the west coast/queenstown/cradle mountain so this was supposed to be a 'scouting' trip anyway of sorts if I were to one day do/take part in/organize a more car-focused trip. As for the boat, it wasn't bad. Well it was bad, but not in the way you're thinking. We did the night trip which leaves at 6:45 (though you have to be there ~2 hours earlier) and arrives the next morning at about 6am. There is nothing to do on the ship. If you plan accordingly and bring a book/tablet/show to watch/charger you can just chill out, take some Travacalm and just sleep through it. The food there is an extremely basic buffet that costs $32 a plate, or $14 for a $3 pizza. The way back we had a travel kettle and a few different types of cup noodles and made our own tea/coffee in the room. This was a far superior way to do it. At the very least book one of the rooms with beds. I guess as we were in the off season we didn't have room mates. You get an option for rooms with 4 beds (2x bunks) or a room with just the two bottom beds. There's also some option for a deluxe queen bed but it's much pricer. We've been on sleeper trains in Asia before so we figured this is similar (and it was)
    • You just gotta be really, really, really clear and decisive with what you want your end product to be. 99% of people who want this conversion aren't "I want to run a 295 front tyre!" so they don't really need the widebody. They just want the OEM body to look a little less dumpy, so bonnet, bar, skirts job done with some camber, stretch, slam. It's when you want that, but then decide to pivot later you get big problems. See also if you're willing to get an all in one fibreglass bar, and you're willing to accept fibreglass problems like cracking the entire item on a driveway, instead of just a piece attached to the bottom, etc etc etc. Decide this all before buyin'.
×
×
  • Create New...