Jump to content
SAU Community

Summernats grand champion a car theif...

Binky1970
 Share

Recommended Posts

Binky1970 Rising Star

Binky1970

Posted
Posted

I "borrowed" this from another thread....

Show car champ jailed

By LOUISE TURK

May 13, 2005

A DAPTO man regarded as one of Australia's best show car enthusiasts was jailed yesterday for his involvement in an Illawarra-based car rebirthing racket.

John David Ritchie - also known as Dave Ritchie - will spend the next two years and three months behind bars after being convicted of multiple car stealing charges.

The 33-year-old unemployed man was part of a crime syndicate which stole dozens of cars across the Illawarra in 2003. They stripped vehicles and torched them in pre-arranged insurance claims or refitted them with new parts and sold them to unsuspecting buyers.

Wollongong District Court heard that Ritchie, of Barellan Ave, was highly skilled in show car restoration and had won titles in Australia's premier street machine event Summernats.

Ritchie is well known among car enthusiasts for his restoration of a two-tone green 1965 Ford XP Falcon coupe.

The $150,000 show car, which took five months to rebuild, has taken out numerous awards at a national and state level.

While Ritchie's talents for car restoration earned him praise and recognition for the restored Ford coupe, his skills were also used for criminal activity.

The court heard that Ritchie was part of a car rebirthing racket which included Stephen Fairall, 25, of Dapto; Scott Field, 33 of Dapto; and Terry Peter Stumbles, of Dapto.

Fairall and Field have been sentenced to prison terms this week for their involvement in the racket. Stumbles will be sentenced today.

Yesterday Judge Joe Phelan said Ritchie - along with co-offenders Fairall and Field - had shown a keen interest and flair for all things mechanical, particularly cars.

"None of these gifts have been the subject of any form of formal training...which would have enabled each of them to have gained employment themselves without stealing other people's property," Judge Phelan said, adding that

written reports revealed Ritchie had a history of being easily led by his peers.

"This seems to be a recurrent theme among each of the offenders so far," the Judge Phelan said.

Ritchie pleaded guilty to attempting to steal from a motor vehicle; two counts of concealing a serious indictable offence; stealing a motor vehicle (a motorcycle and trailer); and stealing a motor vehicle (three motorcycles).

"In light of an established criminal record and matters of dishonesty over some years, and the brazen nature of these offences, and losses involved to various people - including the stealing of bikes for children to be used on holidays - means a prison sentence is inevitable," Judge Phelan said.

He sentenced Ritchie to a three-year jail term with a non-parole period of two years and three months. Ritchie also has been ordered to pay a total compensation bill of $9350 to the owners of the stolen motorcycles.

Roy Grand Master

Roy

Posted
Posted

But the car scene is full of crooks:(

Im not surprised, if love to see the tax returns of certain Auto Salon car owners...and yes i know there are those that work hard and spend all their money on their cars so dont flame me, but the scene does have its share of undesirables

KIL.08S Collaborator

KIL.08S

Posted
Posted

Usually nice enough guys, just make sure you dont leave anything lying around whern there near.

You would think that someone with such a passion for cars would understand what it would feel like to have your car nicked!

Aeris Enthusiast

Aeris

Posted
Posted
If only they'd done them for ALL of the vehicles they'd stolen.

I hate car thieves.

Adrian

Heir heir!!

I agree!!, i still think that auto electocution thing they had in either robocop or starship troopers should be made a real thing :D mind you it'd have have to be 100% certain hehehe

I'm glad they got caught, just cos they're enthusiasts and supposed local hero's doesn't mean they can do whatever they want you think he'd have a respect for other peoples machines if he himself spent that much time and effort on something, i'm the sort of person that if i even accidently bump someone elses car in a car park and there's damage i'd leave my details, as things i spend alot of time on mean so much to me, i value other peoples possessions as well, anyway glad they got caught :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      OK, so a bunch of trim needs to come off to get to the rear shock top mounts. Once the seat is out of the way, the plastic trim needs to come off. Remove 2 clips at the top then slide the trim towards the centre of the car to clear the lower clip Next you need to be able to lift the parcel shelf, which means you need to remove the mid dark trim around the door, and then the upper light trim above the parcel shelf. The mid trim has a clip in the middle to remove first, then lift the lowest trim off the top of the mid trim (unclips). At the top there is a hidden clip on the inner side to release first by pulling inwards, then the main clip releases by pulling the top towards the front of the car. The door seal comes off with the trim, just put them aside. The the lighter upper trim, this is easy to break to top clips so take it carefully. There is a hidden clip towards the bottom and another in the middle to release first by pulling inwards. Once they are out, there are 3 clips along the rear windscreen side of the panel that are hard to get under. This is what the rear of the panel looks like to assist:
×
×
  • Create New...