Jump to content
SAU Community

R32: Changing Front And Rear Brake Pads

HCR32

By HCR32,
in Tutorials / DIY / FAQ

 Share

Recommended Posts

HCR32 Proficient

HCR32

Posted
Posted

Ok as topic says, i just replaced my front and rear brake pads, wasnt hard at all.

Below i got step by step procedure on how to change the pads for those of you who want to save some money and learn something.

1. Get your self an R32 gtst skyline

pad1.jpg

2. Did the rear brake pads first so make sure you put bricks or a heavy object infront of the front tyres so it doesnt move forward while you raise the car on the jack and proceed to take off the wheels. Once the wheels are off you should see

pad2.jpg

Ok, There are basically two ways you can change the pads. One, you can take off the whole caliper by undoing two bolts at the back OR Two(easier), leave the caliper on. I'll show you both ways, first way we will take it off.

3. Undo the two nuts behind the caliper with a size 17 socket. The second bolt you cant see in the pic, its just underneath.

pad8.jpg

One both have been undone the whole caliper should come off. Now the parts we are going to take apart are labeled 1.Bent pin 2.Long pins and 3.X Plate

pad6.jpg

4. Now carefully pull the bent pin out, very easy but careful not to bend it. Once you have done that, you can pull the two long pins down and they should come out easy. Just be careful when your taking out the long pins because the X plate might spring up and go flying some where

pad10.jpg

After you have done the last step the pads should easily come out. If your worried about the piston coming out of the caliper dont worry, unless some one jumps in the car and pushes the brake pedal in.

pad9.jpg

5. Take the back metal plate off the old pads and put them on your new rear pads

pad13.jpg

Ok when i got to this stage, i needed to push the pistons in the caliper back and it cant be pushed back by your thumb...i tried and it didnt work hehe...with limited tools my macgyver in my came out and i thought of this idea. I bolted the caliper back to its original location, then using a big philips head screw driver i pushed the head of the piston back with the help of the disc

pad7.jpg

Ok you know how i told you earlier theres an even easier way to replace the pads, here it is. Once you have moved the pistons on both sides of the caliper back, the new pads should just slide right in, so yes...there was no need to take off the caliper to begin with BUT i didnt know and i found out after i changed the rear right brake :P

pad14.jpg

6. Line up the pads with the holes and insert one of the long pins to hold the pads in place. Next get the X Plate and place it back, please see below pic how 1 of the legs is behind the pin, push the other leg of the X back while you insert the second pin.

pad16.jpg

7. Once both long pins are in, grab the bent pin and feed each side into the top pins like how it was in the begining and thats replaces the rear pads.

pad11.jpg

With the front pads it is exactly the same thing tho i had four pistons to push back rather than two because my R32 is the type M modem with bigger front brakes. 1.the long pins 2.X Plate and 3.Bent Spring

pad15.jpg

Now after you have done all your brakes, go read Brake Pads - Bedding In Instructions - by GenesisR32

thanks

-Barny

cowie165 Veteran

cowie165

Posted
Posted

Hi Barny

I'm keenly waiting to see how it went. Would you mind also posting what tools you used and how much time it took you? I'm guessing when you say brakes you mean changing the rotors or did you mean pads only?

Cheers

Mark

Duncan Grand Master

Duncan

Posted
Posted

Also, if you need to replace the disc it is also easy.

Follow Benny's instructions to step 4, ie take the caliper off the disc. At this stage you can simple remove the disc and replace it. If you are doing the rear disc there is a small handbrake drum in the middle so you need to take release the handbrake first. When you put the new rear disc back on you may need to adjust the drums as well.

Duncan Grand Master

Duncan

Posted
Posted

Yep exactly the same, and for 33 and 34 GTRs as well :) Its a pretty easy job.

Having said that, if you are not sure, don't do it yourself, nothing worse than the brakes not working......

  • 1 year later...
  • 2 months later...
Oosh Veteran

Oosh

Posted
Posted
just thought id mention what id learnt the other day off my uncle while changing my brake pads, to push the pistons back in you could use a G-clamp, which makes it much easier

Mate did that with the rears on his 180SX but they were the screw in type and broke the clamp! :D

  • 1 year later...
jenkies Mentor

jenkies

Posted
Posted

this is awesome fun just completed it this arvo.. real bonding moment with your car.... if u have spare time also give it a few coats of any desired colour followed by clear coat..(use caliper paint as it will take the heat) plus a real clean up so the paint sticks

all up did rotors pads and a lotta coats of paint!! well worth it!

good luck

:thumbsup:

post-27156-1208186029_thumb.jpg

  • 3 months later...
E33 Enthusiast

E33

Posted
Posted

Just a heads up. I find it easier to push the pistons in if you release the bleed nipples on the caliper. Make sure that you either bleed them afterwards or have a hose on the nipple so it sucks in brake fluid instead of air. Also if you don't do the bleed nipple method and just push the caliper pistons in to loosen the master cylinder fill cap. I find it helps a little and makes it easier to push the piston in. Note that if you have added brake fluid in the past ie noticed that the level in the master fluid is low and added more you may find that brake fluid has spilled over the master cylinder brake fluid container when you push the brake pistons in ( keep an eye on the level when you push the pistons in ). Brake fluid is no good for your paint work. So have a wet rag ready and wipe up any brake fluid that gets on your caliper or paint work. Don't get any water near the brake fluid container because water will ruin brake fluid and will need to bleed from the system.

benm Grand Master

benm

Posted
Posted

An even easier way to push the pistons back in is buy a small metal bench vice from your local hardware shop, then cut the clamping faces so they are the same width as the top of the caliper where the pads slide in then insert the vice into the top of the caliper and slowly wind the handle so that the vice pushes the pistons back.

Works extremely well, very fast and only cost about $15.

  • 1 year later...
  • 4 months later...
  • 1 year later...
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...