Jump to content
SAU Community

R33: Aerial Removal

SKYWKR

By SKYWKR,
in Tutorials / DIY / FAQ

 Share

Recommended Posts

Eug Grand Master

Eug

Posted
Posted

mine came like that... personally i dont like the aerial so i fixed it and pulled out teh plug.

this is how i did it:

unscrew the top chrome bit around teh aerial.

open the lining in the trunk, rear left.

take out the jack, and feel around for the motor.

unbolt and unplug teh motor and take it out...

i found that the cogs and the long white plastic thing with teeth were mis-aligned so i took it all apart and cleaned it all up.

regreased and realigned everything.. it is all pretty straight forward if you know

what your doing - if ur not sure then ur better off getting a professional to fix it.

That said - my radio works fine with the aerial down so you might want to leave it???

  • 2 years later...
jjjDavey Collaborator

jjjDavey

Posted
Posted

hey guys ive tried to remove mine, ive unbolted the motor disconnected it but i cant seem to get it out..

the outside chrome part spins but doesn't feel like its unscrewing as far as it should.. any ideas? does it help if the aerial is up or down.

Kinks Grand Master

Kinks

Posted
Posted
the outside chrome part spins but doesn't feel like its unscrewing as far as it should.. any ideas? does it help if the aerial is up or down.

keep going. and the antenna needs to be down or you won't get the motor assembly out of the rear quarter.

  • 1 month later...
Russcoe Apprentice

Russcoe

Posted
Posted
keep going. and the antenna needs to be down or you won't get the motor assembly out of the rear quarter.

Can someone upload a photo of the aerial unit out of a R33, so I can see what I am tugging on. I want the aerial to remain down, so I want to disconnect the electric motor NOT unplug the aerial.

Kinks Grand Master

Kinks

Posted
Posted

the antenna's bolted to a metal sheet that runs down the side of the boot. on the quarter panel side (ie the side you can get your hand to) there's a plug about halfway up that's a standard loom plug, it goes into the main body of the antenna at right angles. squeeze the clip and pull it out. It's white and has about 4 wires going into it.

the actual antenna wire is right up the top, and it goes in at a 45 degree angle.

  • 3 weeks later...
Dingus Proficient

Dingus

Posted
Posted
keep going. and the antenna needs to be down or you won't get the motor assembly out of the rear quarter.

If it's stuck in the up position, how do you force it to go down without snapping it? I'd be happy if mine was down and stayed down, but it's stuck up and just looks stupid.

Russcoe Apprentice

Russcoe

Posted
Posted
If it's stuck in the up position, how do you force it to go down without snapping it? I'd be happy if mine was down and stayed down, but it's stuck up and just looks stupid.

I will unplug mine this weekend and see if I can get reception still.

My aerial was permanently in the upright position. At the mo I just turn the car off, whilst the aerial motor is whuring away trying to decline, I smack the top of the aerial down with the palm of my hand. It takes one hit that is firm but not overboard, then it picks up on the teeth in the motor and goes down. The other way that I first used was to push it down, but the smacking method works for me best as it wont snap or bend the aerial.

Dingus Proficient

Dingus

Posted
Posted

Tried pushing it, it just bends a bit and won't go down. Will try it as the motors going down though and see if that does it. If it's down and the motor's unplugged, but aerial is still plugged in, you should still get reception.

  • 5 weeks later...
Krishy Grand Master

Krishy

Posted
Posted

mine does the same except mine is just a lil bit up and wen i turn the ignition on or turn the car off you can hear the motor grinding....how could i solve that....do i need a new ariel or new motor as i still want to be able to use the lil button behind the steering wheel to have it up or down....anyone got any pics to help me please

  • 2 months later...
  • 2 weeks later...
inthisglass Grand Master

inthisglass

Posted
Posted

some one helped me out and snapped my arial off

so i just had a short and sharp piece of metal left sticking up

al i did was unscrew the silver cap on the outside and pull the rubber mounting bit out then removed the remainder of the arial and put it back together

so i have no arial and still get a 100% perfect signal..

Danyboi Contributor

Danyboi

Posted
Posted

some dick snapped mine off and left it next to the car... what i did.

Cut the top end off so i had 1 inch, and i glued this into the hole where the antenna used to be, So it looks fine, and sits in the metal casing. Had to also remove the white teeth plastic by cutting off and pushing what was left down with a screw driver.

I then unplugged the power from the motor, bu reaching into the boot trim underneath and feeling around, there seems to only be one plug, althernativly you can cut the power coming from the deck to antenna, should be hooked to the REM blue / white wire.

either way, still get perfect reception with the antenna down

  • 2 weeks later...
r33doom Apprentice

r33doom

Posted
Posted

im trying to get my working attena to stay down as it goes up when i turn the car on and down when i turn the car off.. like it nomrally should. however, i want to keep the atenna down. is there a power plug i can disconnect? had a look and i disconnected this grey looking plug, turened on my car, the attena still went up.... so i put the plug back in and felt round the motor, and felt this rubber tube at the bottom of the motor.. is this what i pull out to disconnect power? or...

G0DZLR Mentor

G0DZLR

Posted
Posted
im trying to get my working attena to stay down as it goes up when i turn the car on and down when i turn the car off.. like it nomrally should. however, i want to keep the atenna down. is there a power plug i can disconnect? had a look and i disconnected this grey looking plug, turened on my car, the attena still went up.... so i put the plug back in and felt round the motor, and felt this rubber tube at the bottom of the motor.. is this what i pull out to disconnect power? or...

that or is there a fuse somewhere that can be pulled out?

taipan73 Enthusiast

taipan73

Posted
Posted
im trying to get my working attena to stay down as it goes up when i turn the car on and down when i turn the car off.. like it nomrally should. however, i want to keep the atenna down. is there a power plug i can disconnect? had a look and i disconnected this grey looking plug, turened on my car, the attena still went up.... so i put the plug back in and felt round the motor, and felt this rubber tube at the bottom of the motor.. is this what i pull out to disconnect power? or...

The rubber tube at the bottom of the motor is a water drainage tube...

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • GTSBoy
      Valve clearance for RB25det series 2

      By GTSBoy · Posted

      This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Kinkstaah
      Valve clearance for RB25det series 2

      By Kinkstaah · Posted

      Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
    • soviet_merlin
      Valve clearance for RB25det series 2

      By soviet_merlin · Posted

      To be fair it's the other way around. 300kw is boring in a modern Golf or BMW. They are so competent / well-engineered / devoid of emotion that you have to go stupid fast to feel anything. Whereas the <300kw RB still makes all the right noises and it feels good to drive. Can pull off at the lights with the turbo whooshing and the blow-off pssshing and feel like the coolest kid on the block. Just don't look to the side where you'll see the bored housewifes in their shitbox Yaris/Corolla/Camry that kept up because you didn't go fast at all
    • Dose Pipe Sutututu
      Valve clearance for RB25det series 2

      By Dose Pipe Sutututu · Posted

      300kW is so boring in a Skyline, you'll get spanked by someone's mum's Golf with Alibaba pipes, and an email tune.
×
×
  • Create New...