Jump to content
SAU Community

Recommended Posts

Had a bit of a play last night with an 04 STI WRX.

Top of 4th I hit what I thought to be the rev limiter, no worries, change to 5th....still on some sort of limiter...which I am presuming is a speed limiter..?

That sucks...how do I get rid of it...?

Link to comment
https://www.sau.com.au/forums/topic/75954-wtfr32-gtr-speed-limited/
Share on other sites

it's a 180km/h limitor, you can change/chip the ecu, cut the speed sensor wire (not recomended), or get a HKS speed limit defector. Mine has the speed sensor wire cut (like that when i got it :) ), and it roots up the HICAS.

All JDM cars of that era have 180km/h speed limits, even the R33 and R34 have them. Two options;

Do the dodgy and cut the speed limit sensor wire thing (#53 from memory, I could be wrong though...)

Get an aftermarket/chipped ECU.

Had a bit of a play last night with an 04 STI WRX.

Top of 4th I hit what I thought to be the rev limiter, no worries, change to 5th....still on some sort of limiter...which I am presuming is a speed limiter..?

That sucks...how do I get rid of it...?

Speed limiter.

Get an Apexi power FC or some other aftermarket puter.

Bring it in for a dyno tune/remap and we can remove the limiter, raise the revlimit etc and tune the car for $800.

No point buying an aftermarket limit device when it can be taken out.

Hmmm...have to do something!

With only a Boost increase you'd be close to hitting the limiter before the end of 400m :)

very close, depends on the launch.

Speed limiter is usually about 200kmh which is about 120mph.

near stock GTR's won't normally get there.

Cheers

Ken

very close, depends on the launch.

Speed limiter is usually about 200kmh which is about 120mph.

near stock GTR's won't normally get there.

Cheers

Ken

All jap cars are limited at around 180 kmh ( usualy 185 or so ) .

Bog stock gtrs will hit the speed cutout very easy and depending on model ( if you dont have the limiter ) will go on up to 250 kmh ( r34 gtr ) .

I took my stock 34 to the drag strip ( only mod , catback exhaust ) and i hit the cutout in 4th just after the 400 mt finish line .

You can remove the speed limiter by reprogramming the stock ECU if you have a EPROM writer and know which field to change.

Easiest way if you are not confident with such things (I personally would not want to suff my GTR if I had one) is to take it somewhere who does Performance tuning and ask if they car re-write your stock ECU. Should cost next to nothing.

Cheers

Adrian

The limiter is definatly alot closer to 200 than 180. I have hit it more than once and I can tell you its pretty close to 200, can't be sure cause the speedo only reads to 180, but its WAY past that.

I like it though, enforce me to "keep it real"

The limiter is definatly alot closer to 200 than 180. I have hit it more than once and I can tell you its pretty close to 200, can't be sure cause the speedo only reads to 180, but its WAY past that.

I like it though, enforce me to "keep it real"

They are under 190 k and you can tell by your tacho what speed you are doing .

Well the power stearing gets stuck in 'high speed mode' (heavy round town), The HICAS light comes on after 5 mins (and stayes on), I don't think the HICAS tryies to turn the rear wheels, but it dosn't stop them from moving eather, on big 80km/h round abouts you can feel it move at max g's. I'm trying to find where it's been cut.

192 in an r33 gtst on 265/35/18s according to the GPS. apparently the 32 gtr one is a bit sooner

They are all under 190 k Duncan . 265x35x18's are about 3 % bigger than stock so you are going 3% faster .

They are all under 190 k Duncan . 265x35x18's are about 3 % bigger than stock so you are going 3% faster .

On GPS mate. It don't care how big the tyres are, but they are accurate. Admissable in NZ courts now.

On GPS mate. It don't care how big the tyres are, but they are accurate. Admissable in NZ courts now.

Yes thats what i was about .

The speed was 192 but if it had the correct size tyres it would have been 3% less ,

186 kmh .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
    • OK, if it idles at 1000+ with the AAC, its not an idle airflow problem. The cold start valve just gives extra air when the engine is cold, but you have enough air without it to idle at 1000. I think you are back to a fuel problem, sorry. Can you see the fuel pressure staying constant or does it drop as the revs drop to a stall?  
×
×
  • Create New...