Jump to content
SAU Community

Blow of Valve setup GTR

shaqrx3

By shaqrx3,
in Engines & Forced Induction

 Share

Recommended Posts

DJ984 Mentor

DJ984

Posted
Posted

but they sit open at idle (sucking in air AFTER the afm) so you can't vent them directly to atmosphere (learnt that the hard way)... they suck air in at idle causing stalling and rough as guts idle.

mine had an adapter kit put on them from the previous owner in japan. they vent to atmo and cant suck in any air :cheers:

TTT Grand Master

TTT

Posted
Posted

so you just wanted sound?

anyway,

shaqrx3 - factory bovs are probably the best setup you will get.

but if you must upgrade and want sound, the single greddy type R is fine. it is huge and it will flow more than you will ever make..

Let me know when you want to sell your stock ones.

MELV Experienced

MELV

Posted
Posted
but they sit open at idle (sucking in air AFTER the afm) so you can't vent them directly to atmosphere (learnt that the hard way)... they suck air in at idle causing stalling and rough as guts idle.

mine had an adapter kit put on them from the previous owner in japan. they vent to atmo and cant suck in any air ;)

yes they sit open at idle, which makes tunning a hell of alot easyer.

ask any one that tunes gtrs with AFM's. if you have bigger than stock turbos or BB turbos its hard to get the idle right with an aftermarked BOV.

i had that problem when i got the new turbos on mine, they couldnt get the idle right, because the BB turbos are still spinning damm quick after a bit of wide open throttle.

i also see it as helping the turbos as well, the plumb back system flows air after the intercooler back into the intake. so its breathing in cooler air :)

just my 2c anyway.

lwells Grand Master

lwells

Posted
Posted
anyone know where i can get stockies? ive got blitz one and theyre huge...but then again the BOVs are placed where most cops wouldn't look

They pop up every now and then when rice.. err.. people replace the stockers with aftermarket ones. Just keep an eye on the forsale section.

Lucien.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted
They pop up every now and then when rice.. err.. people replace the stockers with aftermarket ones.  Just keep an eye on the forsale section.

Lucien.

yer, the for sale forum has then come by often enough for a few people every month or two etc.

But most people keep them i think as they know they are arite

lwells Grand Master

lwells

Posted
Posted
yer, the for sale forum has then come by often enough for a few people every month or two etc.

But most people keep them i think as they know they are arite

True, but given the prices on NS (as low as $150 for a "hybrid" copy FMIC) I doubt there is going to be many used ones much lower on here :D

LW.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • Kinkstaah
      Unpeeling the Orange

      By Kinkstaah · Posted

      The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • MBS206
      What brakes on R34 GTT(Europe)

      By MBS206 · Posted

      For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...