Jump to content
SAU Community

R33 as a weekend track racer. Any good?

CrazyNuts
 Share

Recommended Posts

JCMarshall_Law Proficient

JCMarshall_Law

Posted
Posted

I have mine for a while now and I take to track days about 3 times a year, personally I think the 33 is a great car for daily driving and a few fun track days.

Just spend $1000 on the whiteline handling kit and polyurethane (spelling?) bushes all round. Get decent brake pads and keep the car in good condition and you will have a really fun and reliable track car.

When I bought mine, I was thinking I would spend money on getting more power but after my first track day my cash has gone into handling - much more rewarding I think. Having said that I still plan on doing the intercooler, Power FC, boost controller.

So far I have got Bilstien shocks and springs (damping adjustable up front), front and rear strut braces, whiteline swaybars, polyurethane radius rod bushes, 17" wheels with 235 falcons and bendex ultimate pads all round. Engine mods are just the basic exhaust, pod filter and grounded boost solenoid to give 7psi. All this makes a fun track car and I keep up with skylines with 40kW more power but standard suspension.

I'm just planning on getting a new set of dba4000 front rotors and pineapples (rear subframe bushes) then I'll move onto the engine.

Trust33 Grand Master

Trust33

Posted
Posted

Have another drive of your friends r33 and get another veiw of it.Boost that is.Cause you wont get the turbo to spool quicker than the stockie unless you downgrade.So when you do upgrade the turbo you can kiss your dreams of earlier spoolup.But having said that you could allways throw in a set of cams,or just make do with what you have got with whatever turbo you choose.

R33's are quick and honestly unless you know how to controll drift/oversteer you wont want that much more power to start with unless your suspension setup is an equal match for driver and vehicle.

The mods you have listed are a good power upgrade for the 33.The pfc is a must if you want any hope of making 200rwkw.

Because as you probably have allready have read the stock ecu will run the fuel maps dangerously lean when upping the boost with the above listed mods.

HAPPY BOOSTING :)

CrazyNuts Apprentice

CrazyNuts

Posted
  • Author
Posted
R32's make better track cars..

I don't want to get an older car than 10 years. Plus i don't really like the look of the R32

I think a stock R33 with suspension mods will suit me fine. I don't want to build Gondzilla...i just want something fun.

When i DO get a dedicated track car, i will be looking at a R32 GTR and mod the shit out of that instead.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      PXL_20250828_063541093.TS.mp4
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • PranK
      R35 GT-R production ends after 18 years

      By PranK · Posted

    • SteveL
      Leak from Tokico BM50 Brake Master Cylinder

      By SteveL · Posted

      I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...