Jump to content
SAU Community

Recommended Posts

I'm 16 and have always been a skyline enthusiast.

i had been telling my dad that the skyline is the car for me, but he did not approve because they come stock turbo. :werd:

Recently my dad's freind knew of this guy that imports cars from japan to Australia and recently brought one in.

For a price of 14,000 my dad and i went to check it out.

when we got there we popd the hood then had a look at the registration.

it said " Nissan Skyline r33.:"

it is not turbo and i cannot find if its a gts, or whatever. all it has is a gt at the sides and an "s" at the front.

its a twin cam 24 valve non turbo skyline.

to me, ive never heard of just a Nissan skyline r33.

its a 1995 model.

ive never heard of just a nissan skyline r33 gt

please give your thourghts on what it is? :confused:

it may not have turbo but i blown away by the amount of take of acceleration it has.

cheers

FLYR33

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/
Share on other sites

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

check the blue plate in the back left hand corner. a non turbo will say where the engine is RB25DE. a turbo will say RB25DET. Thats how you can tell, if not check the in side dash, if it has a built in boost guage where the rpm tacho is.

these are just some ways that you can tell

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1409820
Share on other sites

Take care it isn't a GTS, those have the SOHC 2.0L engine - will have for the engine designation RB20E on the firewall plate if it is. They are 'somewhat' underpowered....

Most likely it is a GTS25, as mentioned that will have RB25DE on the firewall plate. 200HP from the NA 2.5 means they are fairly quick.....

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1409917
Share on other sites

ok the plate is on the firewall most usually on the left side.

the firewall is at the back of the engine, the wall that seperates the engine from the cabin.

NA means Naturally Aspirated, which means non-turbo.

Hope that clears up some confusion

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1411440
Share on other sites

I've got a Rb20E mate and theyre not that bad, good car to learn on, still pisses on lancers and shit like that, so i wouldnt worry too much if thats what it is, rb25's are good motors, and by the sounds of the 24valve it sounds like one!

Goodluck, and lets hope its a good car!

It should also say on the compliance plate which is a green plate mines on top of the strut tower, and it'll say what make it is and who its complianced by and the date!

Dayne

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1411549
Share on other sites

ok the plate is on the firewall most usually on the left side.

the firewall is at the back of the engine, the wall that seperates the engine from the cabin.

That's left hand side as you look from the front of the car toward the back of the engine bay. Just to the left of the brake master cylinder.

24 valve - yup, that would indicate a RB25DE (GTS25) as I think the RB20E (GTS) is 12 valve due to the SOHC head?

Dayne - yup, GTS's are still better than a lot of cars out there! Just be sure that you don't pay a premium for one. In NZ the GTSs are significantly cheaper (and thus far more common) than the GTS25s.

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1414094
Share on other sites

ok the plate is on the firewall most usually on the left side.

the firewall is at the back of the engine, the wall that seperates the engine from the cabin.

NA means Naturally Aspirated, which means non-turbo.

Hope that clears up some confusion

THANKS MATE

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1414363
Share on other sites

The GT badge on the side of the car has nothing to do with the cars motor. It is just the famous GT badge associated with Skylines.

In the R33 range as said earlier:

GTS = 2lt Non turbo.

GTS25 = 2.5lt Non turbo

GTS25T = 2.5lt Single turbo

GTS4 = 2.5lt Single turbo or NA + 4wd

GTR = 2.6lt Twin Turbo 4wd

All very good cars. Not a fan of non turbo Skylines though as I think it defeats the point.

I know that coment will cause some tension. i might just run and hide under my turbo...

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1416015
Share on other sites

Dayne - yup, GTS's are still better than a lot of cars out there! Just be sure that you don't pay a premium for one. In NZ the GTSs are significantly cheaper (and thus far more common) than the GTS25s.

Got mine at a good price anyways:) considering upgrading to RB20det in it this holidays though.. or 25DE

Dayne

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1416155
Share on other sites

The GT badge on the side of the car has nothing to do with the cars motor. It is just the famous GT badge associated with Skylines.

In the R33 range as said earlier:

GTS = 2lt Non turbo.  

GTS25 = 2.5lt Non turbo

GTS25T = 2.5lt Single turbo

GTS4 = 2.5lt Single turbo or NA + 4wd

GTR = 2.6lt Twin Turbo 4wd

All very good cars. Not a fan of non turbo Skylines though as I think it defeats the point.  

I know that coment will cause some tension. i might just run and hide under my turbo...

thats like saying getting a standard commodore without a supercharger defeats the point.

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1416173
Share on other sites

GTS4 = 2.5lt Single turbo or NA + 4wd

I have never heard of an R33 GTS4 Turbo, all the 33 GTS4's I've seen have been NA

The only other single turbo GTS4 I've seen is an R32 GTS4.

and before someone makes a smart arsed comment, GTR's with single turbo conversions dont count :(;)

Link to comment
https://www.sau.com.au/forums/topic/76999-skyline-r33/#findComment-1417072
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...