Jump to content
SAU Community

Recommended Posts

I Just picked this up from the SHIFT PERFORMANCE website.

It is advertising a Apexi TURBO TIMER. Then in brackets it says "for turbo and NA Vehicles)" why would it advertise it for NA vehicles if NA vehicles are not TURBO.

why would people buy it?.. :confused: :werd:

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/
Share on other sites

A turbo timer just makes your car run for a preset period after you take out the keys, so the turbo has time to cool down a bit before it turns off.

Obviously it works on ALL vehicles. NA included, if one desired.

thanks mate

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1414414
Share on other sites

i use one. on my NA skyline. I dont see the harm in lettin my engine warm down after im hammering it at 120km+. i also use it to warm up my engine on cold days in the morning, for when im stoppin to get out and grab a newspaper or something else trivial, to measure my voltage when im running my stereo with the engine off, and for a couple of other reasons that im sure i could think of.

Dont say that NA's use them for wank factor cuz my reasons are all legitimate, and also their not illegal in WA.

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1414935
Share on other sites

']i use one. on my NA skyline. I dont see the harm in lettin my engine warm down after im hammering it at 120km+. i also use it to warm up my engine on cold days in the morning, for when im stoppin to get out and grab a newspaper or something else trivial, to measure my voltage when im running my stereo with the engine off, and for a couple of other reasons that im sure i could think of.

Dont say that NA's use them for wank factor cuz my reasons are all legitimate, and also their not illegal in WA.

are all turbo timers the same.

do i have to get a specific one to do what your one does with the cooling and warming up of the engine?

How does it warm up the engine? when you could just turn on ya car?

can you tell me how they work .............please ;)

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1420386
Share on other sites

Turbo timers are designed to simply let the car run for a desired period of time after turning off the key. Some of the new ones even have there own calculations on how long your car should run for. They were built for turbo cars, because turbos use the engines oil for cooling and lubrication, after "giving one a hard time" the oil temperatures rise dramatcially, letting the car run down gives the turbo and oil a chance to cool down as the oil is still flowing through the turbo. Shutting a turbo down straight away while the turbo is still hot allows the oil to bake on things like bearings, shafts and seals forming a hard abrasive substence causing huge wear and sometimes seizing the turbo.

If they were required on NA cars, drag cars would not shut down there engines as they cross the line, they are not beneficial to NA cars.

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1420462
Share on other sites

How does it warm up the engine? when you could  just turn on ya  car?

you just turn the car on and then turn it off to let the turbo timer keep the engine running, so you can leave the car running when you run in to get the paper etc on the morning, with out leaving your keys in the car, as most of them turn off when the hand brake is released

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1421598
Share on other sites

If they were required on NA cars, drag cars would not shut down there engines as they cross the line, they are not beneficial to NA cars.

:P

Right, so because a dedicated race engine that probably gets pulled down and rebuilt after every meet doesn't need something, then why would a street car that is expected to do hundreds of thousands of kilometres without stripping down have to worry about it?

Drag cars don't run air filters. I guess they're not necessary either.

FI race cars don't use turbo timers either, and no manufacturer ships with one. Clearly if they don't think its necessary in a race situation or to avoid warranty claims on street cars, they're not beneficial on FI cars either.

JGTC cars also run 12.x:1 compression and a fair whack of boost; want to try that on your street engine?

Here's a hint: never use what goes on with a race engine as an example of what's right to do in terms of maintenance and longevity for a street engine. Unless you can afford to replace or rebuild your engine as often as race teams pull down theirs.

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1421636
Share on other sites

I wasnt talking about top fuel cars or dedicated race engines, i was talking about big NA street cars that do, do a hundred thousand k's between rebuilds.

Holden Astra turbo's and a few others do come with turbo timers standard so that was also a bad example.

My point is they are not beneficial to an NA engine, and to date no one has been able to find a valid reason why they are.

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1422729
Share on other sites

they actualy do more harm than good to an N/A vehicle. :thumbsup:

on idle, the A/f mixtures are rich, which eventually washes any oil off the cylinder chamber walls, causing more engine wear....

Why do you think most car manufacturers recomend you warm up your car in the mornings for only 30 - 60 seconds??

It's beneficial for a turbo b/c the cost of saving the turbo outweighs the engine wear factor.

Even better are the pumps that circulate oil through your turbo after you have shut the engine down. I have yet to see one though....

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1422772
Share on other sites

whats the harm in letting a NA skyline's oil cool down for a minute or two, lolz let people do it if they want...its just like letting it idle for a few minutes while u go to ur gf's door and wait for her and then u find out shes not ready and u have to wait a further 10 minutes :bs:

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1422947
Share on other sites

whats the harm in letting a NA skyline's oil cool down for a minute or two, lolz let people do it if they want...

Why would an N/A skyline need to cool it's oil down?

Turbo's spool at up to 150000 rpm (maybe more), and it's when the engine is stopped that oil on the bearings starts to cook. The oil is not cooking itself, the hot bearing are.

Unless you have removed the rev limiter on your N/A so it revs to 150,000 rpm, you are doing damage, not good.

Have a read of this article . In particular look at the reliability section.

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1422988
Share on other sites

the purpose of the turbo timer is to keep the engine running, it wont cool the engine down for peanuts, if anything it will heat the engine up more as there's no airflow into the engine. however as the engine is running so is the oil throughout it, which leads to the oil feed on most turbochargers. the bearings get insanely hot during operation and letting the engine run on idle for a minute allows the oil feed to keep running, which cools the bearings and shaft down. i mean its still gonna be a few hundred degree's after the turbo timer is off but it will drop from maybe a high few hundred deg's to a lower temp by oil and water cooling. if you were driving around giving it some stick and then instantly turn off the bearings will just stop and shaft will too. so the heat stays in and can expand/warp or so forth I guess??

the purpose is to cool the turbocharger parts, not the engine itself

Link to comment
https://www.sau.com.au/forums/topic/77299-turbo-timers/#findComment-1430336
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Haha I do that.. thats when it chirps..The bit point for me is almost non-existent. Otherwise I stall it. But yes, in terms of performance, the clutch is solid af.
    • Greg speaks wisdom. These dirty old Datsuns are only value when they are cheap. When they are not cheap, there is no value. Sounds contradictory, but it's true. We are now 20 years past the hey day of modifying cheap 90s JDM cars for small amounts of money. This is a different world. If you are rich and can afford not to care about what is effectively wasting money on an old Datto shitter, then I have no reason to argue against it. But if you are wanting to experience what we all experienced back in 2005 (and I bought my car last century!) then there is no way to do it.
    • Short answer: No. Medium answer: No, because you still need to conjure the things out of thin air to bolt them to a NA to make it a NA+T. Long Answer: No - The things you need to conjure - meaning a turbo, intercooling, manifolds, exhaust, intake/manifold/piping, clutch, injectors, fuel pump, AFM (?), ECU + Wiring (woo, N/A loom fun) have to come from somewhere. You could have many scavenged these things from an OEM car that someone had upgraded from and use some of these. This will be cost prohibitive now, especially so in the USA. You'd probably pay the same for newer, upgraded components that are better than old OEM stuff from 25-30 years ago. None of these big ticket items are re-usable for the N/A car. Why not buy new and upgrade while you're there? The only real consideration is turbo and fuel sizing and determining whether you want to stay within the bounds of the OEM engine or get into rebuild territory. These limits ARE lower with a N/A motor and especially N/A gearbox at the starting point. And if you're gonna upgrade those then you may as well consider having them built to begin with. Because everyone here knows you're never far from that next engine rebuild once you start making the power you want... The cars you see on the internet and SAU etc have been built over decades. If you're really clued in... you would sell your US car to somebody for what you paid for it. You would then scour AU JDM pages or SAU and buy a car like Dose's on this forum with your powerful American Dollar. This will save you so much money in the long term. Importing it could be tricky. Or it might not because USA. I have long said the only reason 90's Japanese stuff took off was because a) Japanese people had Japanese cars so that is what they used b) Australians could import these cars to Australia with very minimal changes and use them on the road here c) Neither country had well-priced access to US or EU Sports Cars. I don't believe the JDM scene would have taken off in Australia at all if we had EU priced EU BMW M offerings, or more especially the AUS V8 Scene would never have existed if we had the multitude of US cars like Camaros, Mustangs, Corvettes at the prices you folks do. After all - Do the math. I would say put a V8 in your R34 and that's the smart way forward. It is. I did it. I know this from my own experience. But at that point there's no reason to simply not buy a C5 or C6? It would be simpler and easier and cheaper and bette-
    • Reading all this... hurts lol. I have an ENR34 5MT and I paid an inflated USA price for the car alone, had to do tons of preventative maintenance past that, and so I'm over $30K USD into the car already and haven't even touched power.  I wanted to +t it. Not even trying to make GTR numbers, I'd be happy with 250hp.  Can I get away with paying much less to make that happen?
    • Damn you’ve done well, definitely snapping necks.
×
×
  • Create New...