Jump to content
SAU Community

Recommended Posts

I believe this would be a setup, fairly typical of your average 'modded' gtr.

Here's what Ive just done, to my previously stocker RB26

R34 N1's

A/M Dumps s/s

700cc injectors

3" Mandrel Bend, SS Exhaust, Turbo Back

Hi Flow Cat

K&N Pods

Wolf 3D V4 Plugin ECU

That lot has pretty much chewed into my initial 'Stage One' budget, with a little left in the kitty for some dyno hours. I plan to run boost at 1.0 bar for street, and 1.2 for strip.

Im just curious as to what 1/4 mile time I should expect from that? I know a lot will depend on driver, conditions, track etc. but Id just like to know a round about figure. Im hoping to go mid 11's? A bit ambitous, or very possible.

Any advice is appreciated.

Link to comment
https://www.sau.com.au/forums/topic/78477-what-to-expect-typical-gtr-setup/
Share on other sites

Im just curious as to what 1/4 mile time I should expect from that? I know a lot will depend on driver, conditions, track etc. but Id just like to know a round about figure. Im hoping to go mid 11's? A bit ambitous, or very possible.

No, I think you should run in the 11's, although high 11's :(

high 11's alot depending the hp your making and how well the car setup will launch

ie tyres, clutch, and how hard your going to be on it.

cefiro_pwa =got no idea as usual (take a look at the timeslip times verse hp in this forum)

these car are all cross australia unless we all can't drive (or are we going to get the Quote "my mates car" )

OK specs as follow:

G707160-7 GTR Ball Bearing Replacements 375 hp N1 Comp .42 a/r turbine

housing .64a/r

I should mention that Im currently running stock clutch, and by the looks of ppl opinions, I should refrain from trying 1/4 times without upgrading first. For now, I think I'll work on getting a really decent tune, Im really prepared to invest a bit of $$$ in this area.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...