Jump to content
SAU Community

fuel consumption non turbo r32


atmo32
 Share

Recommended Posts

hi, it sounds a bit worse than it should be. When the VLs came out in NZ you had a choice of RB20E or RB30E, apparently the RB30 was more economical because you didnt have to thrash it to get any decent performance out of it. So it may not get as good as you would think for a non-turbo. My Turbo GTS4 gets about 350-400 around town on a tank.

Link to comment
Share on other sites

what temp is it running at - i had a car with a stuck thermostat. Didnt warm up real quick and temp fluctuated on the highway - down to cold. New therm gave anoter 40km a tank

Just see where your temp sits.

Run some good injector cleaner (the concentrate) I tnink it is redex (about $12) but soes a lot of tanks.

Clean the AFM with contact cleaner. pump the tyres up.

There the cheap options...

02 sensor could be stuffed like baseliez is saying. you could replace that for about 50 or 60, may be wotrth it - unless you get exhaust gas analysis to see what AFR it is running at idle and part throttle

Link to comment
Share on other sites

if temp remains at 1/2 most of the time then your thermo is probably ok.

Other things to change -

fuel filter,

and possibly air filter and spark plugs.

02 sensor more likely though.

I dont think the responsiveness has much to do with it unless you are driving it a lot harder

Link to comment
Share on other sites

try some fuel injector cleaner.. I have always been dubious about them, but after replacing everything else, and the o2 sensor.. injector cleaner *seems* to have made the biggest difference.

Gone from about 350 a tank, up to 500 a tank, mix of city and highway driving... all with a bottle of injector cleaner. That is pretty much going from 15L/100km back down to 12L/100km(!). This is on an RB20DET, and I am usually fairly heavy footed.

Link to comment
Share on other sites

Baze, its in the bottom hose, 3 bolts. when i replaced it, was between 30-40$

also, nissan recommend to use sealant to seal the thermo housing, but i was slack and just got a VL Thermo gasket-$3

Link to comment
Share on other sites

managed to get 600km (1/2 highway driving) out of R32 gtst sedan with stock rb20det (cat back exhaust and filter panel), so 550km in ceffy is quite possible??

600km was done with never reving it past 3000 rpm, keeping it off boost :rant:

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Agreed with the rest. Also at least based on my own research, there are no readily available stock or close-to-stock RB20Neo maps that you could download and use as a base were you to buy a complete standalone ECU, and the regular 20DET maps don't really work well so you'd need to take it to a tuner if you have no experience. I installed an AEM V2 on my 20Neo+T and had lots of headaches until I got it to run and idle properly but I've yet to remap it fully. You have to start building up your timing and fuel maps entirely from the ground up; even the ones for a 25 didn't work at all.
    • Got some decent progress after work yesterday and also today. Got the ECU all wired and passenger side interior all back together. Kept the wiring up nice and high to avoid people standing on it. Got the surge tank relays rewired and tidied up the pump wiring and cut a hole to bring the cables through.  I found a spare USB cable I had lying around so I decided to cut it up and see if I could use it for my CAN 1 bus. Turned out one of the pins I needed was to the shield of the cable so i cut it up and desoldered it and resoldered to the correct pins.  Had the issue with the powersteering hose hitting the A/C compressor and fan shroud. I pulled the bracket off and modified it to remove the front mounting point which now clears it all. Will keep an eye on it to see if theres any signs of fouling once it's up and running.
    • That's some good input mate. Nice.
    • So today I went well outside my comfort zone (again) to replace my valve cover gasket.  I have had a big leak over the exhaust leading to a lot of smoke and smell every time I drove it. The leak was in the rear driver's corner.  The job wasn't hard as such, just a bit finicky and time consuming.  The old gasket was rock hard and broken right where the leak was.  The leaky corner had so much sitting oil in it.  The good news to my amateur eyes was no buildup or sludge under the cover. It all looked fairly nice in there.   I haven't started it yet. I ran out of light and body when putting the coils and injector loom back in. Probs only 30min left for the morning.  I was so nervous putting the cover back on, I must have lifted it 5 times to make sure the gasket was still seated properly. God it's going to be nice to be leak free and not make other traffic light queuers think my car is about to explode.
    • Gave the Mazda it's first wash, it will need some clay, a light compound, and polish polish to remove a few swirl marks, but that will be a job for when I have a full day to get my DA polisher action on
×
×
  • Create New...