Jump to content
SAU Community

Recommended Posts

hi all,

i have a matching set of GTR crank and rods.. i think it was out of a R32 gtr ..engine had done 72000kms.. were replaced with a 2.7ltr hks kit.

GTR Crankshaft - 450bucks - Pretty FIRM

GTR Connecting Rods - 200bucks - Pretty FIRM

*OR offers around 700 for the SET posted.

Crank and Rods.*

Photos coming shortly. if anyone is interested.

Would Prefer Victorian Buyer - As pick up would be easier on most these items. Postage is NOT included in any of the prices. unless stated

Reason for sale - contemplating going RB25/30 instead of RB24.

IF you have a problem with the price dont slag me off .. either pm me a suggestion or just keep it to yourself . thanks :Pimp2:

Regards

Matt :chairshot

need to sell these ASAP .. will take offer .... REASONABLE ones not insults

Crank packaged ready to be posted..... previous buyer pulled out.

Link to comment
https://www.sau.com.au/forums/topic/80047-eoi-matching-gtr-crank-and-rods/
Share on other sites

Just looking for interest at the moment

i have a matching set of GTR crank and rods.. i think it was out of a R32 gtr ..engine had done 72000kms.. were replaced with a 2.7ltr hks kit.

GTR Crankshaft - 800bucks - Pretty FIRM

GTR Connecting Rods - 300bucks - Pretty FIRM

also have  

- Standard GTR Fuel Rail - 50bucks

- Standard GTR Fuel Injectors - 300bucks

- Standard RB20 DET Silvertop Block - Crank - Rods - Pistons - 300bucks

(basically complete with head / plenum / cross over pipe n bov / exh manifold / water pump / oil pump - but head needs line bore on the cam tunnels as the journal bolts siezed in two of the inlet side caps. rest of caps are here.. but would be easier to pick up another head)

- Also a box of bits with it as well ..fuel rail ..ignitors .. CAS's dunno if any of its good .. but it goes with the engine.

Would Prefer Victorian Buyer - As pick up would be easier on most these items. Postage is NOT included in any of the prices.

Reason for sale - contemplating going RB25/30 instead of RB24.  

IF you have a problem with the price dont slag me off .. either pm me a suggestion or just keep it to yourself . thanks :Pimp2:  

Regards  

Matt  :chairshot

Hi matt,

I'll take the RB20DET off you for 300. I'm in Melbourne so can pickup

bump

willing to take offers on the gtr crank and rods if anyone is at all interested.. we can work out some sort of a deal .... need to let them go

pm me if u wana discuss it

Matt

do you know anything about putting gtr crank and rods into RB25?

If so, PM me and we can talk about it.

And depending on out come you may have interested buyer ;) *points at self*

Cheers

I want the crank and will take it asap, I have sent you a PM...

Oh also I might be interested in the injectors and rods too but send me a PM with your contact details.

Daniel

Matt I will take that crank no dicking you around no arguing on the price I am deadset if you are still trying to get rid of it PM and I will send you my address and you can COD it today....

  • 2 weeks later...
Matt I will take that crank no dicking you around no arguing on the price I am deadset if you are still trying to get rid of it PM and I will send you my address and you can COD it today....

S13 Drifter found other means ... so the crank is still available

Crank and Rods Price Drop ...... need to sell ASAP

call or Sms 0405139253

Matt

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Reading through the engine service manual their advice is do a cylinder balance test. Unplug one injector at a time and see if the idle drops a consistent RPM. You can also do this using a Consult cable which is easier. They also call for unplugging the power transistor, then with the engine off and the fuel rail unhooked from the manifold verifying that you have good fuel flow (even injection, no dripping/leaks, etc) when you twist the CAS by hand. Also verify the spark by pulling the spark plugs and allowing the plugs to ground and turning the CAS by hand. I would also start doing the sensor checks and idle valve checks in service manual. Make sure the MAF tests reasonably, the intake air regulator is sane, etc. You may have to get new spark plugs.
    • This sounds very old of me, however since buying the Tiguan shit box, my view on shit boxes have changed.
    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
×
×
  • Create New...