Jump to content
SAU Community

Recommended Posts

This is a guide to help people make an edcuated desision on how much a PFC costs to tune and where they can get it done.

I ask for each entry to include the following info.

1. COST

2. Mods you have done (mechanical mods not stereo mods)

3. Where u did it

4. How long it took

5. Comments (was happy was not happy and why)

Link to comment
https://www.sau.com.au/forums/topic/83131-price-guide-pfc-tuning/
Share on other sites

  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

ohohoh me first

1. $550

2. High flow turbo, 3" turbo back w/ hi flow cat, HKS timing gear, 040 fuel pump, 6 x S15 injectors, Z32 Afm, Blitz id-III, fuel pressure reg, HKS SSQV.

3. APC

4. About 4 hours

5. Very happy with the tune, had to take back once after timing gear was done to re-adjust but this was only $100 cause it was only a half and hour to re-do. NOTE: This was first done 2 years ago. So price is old and now could be more or less... I dont have timeto shop around too much so i ask others where and how much.

Reason i ask is that i fryed by pfc due to a bad jump start so i am back in the market for a new one so ive ordered the d version so i can go to a MAP sensor and ditch the afm. So i need to get it done from stractch again. APC is far from home now and id like someone closer if possible.

Please post results and price from all areas of AUST as this is now a tech thread for others to be able to go to the right place first time.

Cheers Col

1. $550

2. FMIC, 3" exhaust (turbo back), PFC, cam gears, fuel pump and reg, HD clutch, AVC-R

3. tuned by Paul from Hunter Thomas Automotive, tuned in sydney at ProCar Racing

4. dunno he took the car to sydney for a day

5. very happy made 220 rwkw on stock turbo, cars runs so nice now, idles smoothly, accelerates properly, and uses less petrol A+++++++++++++++ rating for sure

Charged: $100

Mods: FMIC, 3" Turbo Back Exhaust, PFC, RB30DET.

Tuned By: Shaun @ Boostworx in Adelaide, SA

Time Taken: 1hr (I Hung Around)

Comments: Very happy, The 3ltr only 'just' ran on the stock RB20DET 2ltr PFC base map. Very good tune for bugger all bills.

The tune was 90% wot tuning with a few little light load adjustments.

It made 176rwkw with the stock RB20DET turbo running 9psi @ 4400rpm-4950rpm, power drops off rapidly after this rpm.

I've reached the limit of the stock rb20 turbo and injectors as they are hitting 100%.

I will be installing injectors and a larger turbo soon, I've been told the tune will cost $200-$300 as he will have to completely go over the light load map. This is what takes time, not the WOT.

  • 2 weeks later...

Any more takers... Common people have pfc's left right and centre. I have had many PM's... please post here not pm me...

I need to be tuned next monday and im shocked by the price these days. All shops i have called are going towards the $800 mark...

Guest Variable

1. $540 (4hrs Dyno time - SAU Discount)

2. Exhaust, Cam gears, running 1 bar boost

3. Mercury Motorsport (They have fc-datalogit for all power FC's)

4. Dropped off Wednesday night, ready lunch time Friday

5. Very happy, cold start needs a bit more work, power went from 221 awkW to 245awkw)

6. Car: R32GTR

Power FC tune is $450 minus 10% to SAUWA members

We normally have the car for 1 day.

HP varies but never seen one leave yet that made less hp.

We actually do a special on R33 GTS-T's and Silvia SR20DET's of supplying, tuning and fitting a Power FCwith handcontroller for $1600. We use Datalogit to tune them as well and that includes a full Dyno Dynamics Shootout accredited power run.

Don't think there are too many shops who can beat that :)

Trouble is for the majority is we are based in WA :P

cheers

Ken

  • 3 weeks later...

1. $500

2. catback exhaust, fmic, bosch 040, pfc, pod

3. hitman (penrith)

4. about 3 hours

5. excellleeent! top guy as well highly recommend.. even fixed my boost gauge & z32 wiring! first run 127rwkw :D after tunning 182rwkw :P there was something very wrong with my car haha..

6. r33 gts-t s2

  hanyou said:
1. $500

2. catback exhaust, fmic, bosch 040, pfc, pod

3. hitman (penrith)

4. about 3 hours

5. excellleeent! top guy as well highly recommend.. even fixed my boost gauge & z32 wiring! first run 127rwkw :) after tunning 182rwkw :)  there was something very wrong with my car haha..

6. r33 gts-t s2

Particulalrly interested in this one, cause when i FINALLY get around to getting mine done, i think I'm going with The Hitman

Was the $500 for road tune or dyno tune...or bits of both?

Thanks..Birnie

dont just get a full outright power tune cos youll get shit ass economy. the majority of your driving is done in the first 10x10 cells. these should be tuned on partial throttle, medium throttle and low throttle to get your fuel economy. its easy to do full throttle tune and get a max top rwkw sure but your fuel economy will suck

  • 3 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Can't you put the pistons to TDC and then do the valve seals? Or will the drop down too far to pull them back up?
    • One thing I can tell you is, do it properly the first time. If you encounter unexpected problems just let the car sit for a week or two if you have to get some other parts or figure stuff out.  I'd have said go and use as many OEM parts as possible but since you want to change the turbo later on a custom kit is probably the better choice. Since I have no experience with RB25 just compare parts diagrams and images before buying a line kit and it should be easy to see if it has everything you need. Amayama has very good parts diagrams and part number lists, that is what I used a bunch to figure out what I might need. And don't forget to plan ahead and possibly renew other stuff that's easy to get to while you're in there doing the turbo lines. Happy wrenching
    • Update 4:   Hi all, good news. Engine is running and all the gaskets and seals seem to be working as intended. No leaks so far, even the JB Weld seems to hold. I flushed out the old coolant a few times and put in fresh coolant, not Nissan stuff, I decided to try the Ravenol Protect FL22, they claim it works for a wide variety of JDM cars and the opinions on it by some people were pretty good. And it has the nice poison green color! And man am I glad I bought a coolant system tester earlier this year, vacuum filling works wonders on this engine. I can definitely recommend this to anyone still doing it the old school way. All you need is compressed air supply. Will have to do a small test drive as soon as I can, I removed the gauge cluster again as the tacho needle was still bouncing around a bit but it was much better than before already.  I also found some cracks on all 4 tires inner and outer sidewalls. Apparently these tires should 't be parked on for extended periods or be kept under 0 degrees during storage, which I did not know. Clearly the previous owner didn't look into those details either, he probably bought them just cause they are cool semi-slicks. I'm just wondering how tf I am supposed to reach 30-80 degree tire temperatures on the public road consistenly, these tires were never going to work for my use case. I'll probably order Continental SportContact7 ones as these are the best allround summer tire available right now and I don't think I'll need anything crazier for now. Do let me know if you have experience with various tires and which ones you recommend.
    • You have no idea how many goddamn boxes I received these past three months haha Most have been put to use by now though, luckily
    • Not going to pretend I didn't do a bit of junky work this time around, but mostly due to the fact that some things I am not willing to spend days fixing right now, like wiring. I try to do most things properly the first time around.
×
×
  • Create New...