Jump to content
SAU Community

Recommended Posts

Help for the searchers, alternate names.

Oxygen Sensor, Lambda Sensor, O2 sensor, A/F Ratio Sensor, Narrow and Slow A/F Ratio Sensor, Not a Fast and Wide Lambda Sensor

------------------------------------------------------------------------------------------

I figured it was time to have a dedicated Stagea lambda sensor selection, buying, wiring and fitting thread. There is a lot of info but it is spread out in a number of incomplete threads. So I hope this one will cover everything, with your help of course.

I bought a new lambda sensor from my local Repco yesterday, ACA brand part number ROX207 for an EL Falcon cost $77.97 inc GST. It has 3 wires, 2 black and 1 blue. I will cut the wires and connect it to the Nissan plug via connectors as stainless steel wires do not take solder. They are stainless steel to take the heat, copper or aluminium would simply melt.

Pictures would be here, but I can't figure out how to upload.............

:blink: cheers :)

Link to comment
https://www.sau.com.au/forums/topic/83819-fitting-a-new-lambda-sensor/
Share on other sites

Hi SK,

Ive bought a Repco 'ACA ROX207' oxygen sensor to suit Ford EL. Cost $81. Has 3 wires connecting to a plug; 1 blue wire (by itself in the plug connection), and 2 black wires side by side next to the blue wire.

I hope this is the right one!

Having the Stagea serviced in a few days time (80000km), adding a small body 3inch Catco cat converter (from batmbl), a 3inch stainless single turbo to cat dump pipe (from Just Jap off ebay), a Black Widow car alarm (for insurance sake; thanks Shannons!), a Hybrid EBC (off ebay), an Apexi SAFC II (off ebay), and an R34 GTT intercooler (from member: Ed). With a K&N pod filter and Dayz Special Edition cat-back 3inch mild steel exhaust it should all run well together.

With all of the above fitted and dynoed, hopefully power increases a fair bit, and the fuel issue is 'sort of' fixed with the new O2 sensor.

Once it's all tuned I'll post up a detail of litres per 100kms. And maybe a dyno graph, if it's impressive enough!

Brendan

I cut off the Ford plug and then I checked the lambda sensor plug (three pin) on the Stagea and BINGO it is the same as the lambda sensor plug on the R32GTST. So I cut off the old R32GTST lambda sensor and then used a crimp joiner to attached the three wires, 2 X blacks to the outside pins and the 1 X blue to the inside pin.

Picture will go here when I figure out what's wrong with the upload facility.

The lambda sensor is 22mm, and I have a big 22mm ring spanner that should do the job just nicely. Remove the old lambda sensor and screw in the new one.

Picture will go here when I figure out what's wrong with the upload facility.

Then plug the new lambda sensor in,

Picture will go here when I figure out what's wrong with the upload facility.

Fill the Stagea up on the way to work tomorrow and check the fuel economy over the next week or so. I will post up before and after results

:) cheers ;)

Edited by Sydneykid
After replacing the o2, how should i go about resetting my ECU?

I am not going to bother, I don't think it makes any difference when you don't have any error codes.

You can unplug the ECU, that resets it. Or unplug the battery and stomp on the brake pedal (with the igntion switch on) a few times to make sure all the power is drained. I hate doing that as the clock looses its time and the radio looses all of it preset stations.

:) cheers ;)

For some reason, the bolt in my ECU plug has had its head snapped off.... is it time for me to dremel the bastard out (something i am not happy to think about with all those wires there...)

My guess is someone has tried to tighten the bolt up with the plug not aligned. I would drill it and use an easyout. Much neater.

SK - Do O2 sensors wear out ? Would it be good practise to change the one on my 15 YO R32 ?? Even though it seems to be running fine ?

Nissan recommends changing them every 40,000k's. They don't "wear out" in a mechanical sense. They just get contaminated and don't read the A/F ratios properly.

:P cheers :)

Edited by Sydneykid

Got my new o2 today! YAY (original nissan from jp)

o26me.jpg

Will go ahead and do the swap this weekend, saturday morning. Will do spark plugs at the same time.

Ill take photos while i do it and do a little write up for everyone...its original so its litterally screw out - screw in.

Anyway, ill post back saturday night,

Alex

Edited by AlexCim
  • Like 1

The gallery is working, so here is the picture of the Falcon lambda sensor with the R32GTST plug fitted to the wiring harness using crimp connectors.

Lambda_Sensor.jpg

The 7 day fuel economy test is underway, results tomorrow.

:D cheers :)

Edited by Sydneykid
Got my new o2 today! YAY (original nissan from jp)

...

Alex

How are you going getting the old one out? I tried today and gave up getting a spanner in.. I've rung around town and nobody seems to have the 'oxygen sensor socket' in stock either...

Edit: and slightly off topic, SK - How did you get the gallery working? Is there something special you have to do/be to post images there? I just went over to it, and cant find any button or menu to upload images...

Ian

Edited by ian

Over the weekend i went to try to install my new split dump and front... it ended up not fitting so on the way putting everything back, i put in the new O2...

Unfortunatly, this means i have no photos or anything, but its relativly easy to remove your dump pipe (i could probably do it now in around 1 hour)

The OTHER way around it could be like this...

1. remove engine heat sheild

2. remove the top three bolts holding in the brace, take brace off

3. undo the screws holding on the heat cover on the dump pipe

4. replace o2

5. reverse

I could probably help you out doing it if you want, but not this weekend (too many essays due)...next weekend would be fine.

Ill give my fuel economy report too... still yet to fill her up. I replaced my spark plugs at the same time, the old one were pretty rooted.

4.

How are you going getting the old one out? I tried today and gave up getting a spanner in.. I've rung around town and nobody seems to have the 'oxygen sensor socket' in stock either...

Edit: and slightly off topic, SK - How did you get the gallery working? Is there something special you have to do/be to post images there? I just went over to it, and cant find any button or menu to upload images...

Ian

I used a 22mm ring open ender, it was tricky but it worked.

The Gallery works OK, I just went to "My Photos" (it's on the left top) then "Upload Photos" (that's on the right top). "Browse" to where the photos are on your hard drive. Then "Upload/Submit". Pretty simple actually.

:P cheers :)

Edited by Sydneykid
The Gallery works OK, I just went to "My Photos" (it's on the left top) then "Upload Photos" (that's on the right top).  "Browse" to where the photos are on your hard drive.  Then "Upload/Submit". Pretty simple actually.

:O cheers  :D

ah, that explains it - I have no "My Photos" option, I'll do a post in the right section to say I have a problem..

Ian

Got my new o2 today! YAY (original nissan from jp)

o26me.jpg

Will go ahead and do the swap this weekend, saturday morning. Will do spark plugs at the same time.

Ill take photos while i do it and do a little write up for everyone...its original so its litterally screw out - screw in.

Anyway, ill post back saturday night,

Alex

Slightly OT but what was the part number of the o2 sensor you got from nissan? It looks like it has 2 black wires and 1 white or is that correct or something else? oh one last question, how much?

Sorry for so many questions!

Thanks!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • He obviously had his reason for flipping you off. I wonder what it was...
    • Thats why I stay far, far away from Eastwood. only go there if I wanna eat Korean food 
    • I have to agree like, yesterday, I was driving down the warringah freeway towards the bridge when this jackass driving a beaten up Honda civic cut me off so suddenly it made me almost yank the wheel to avoid him hitting my car. Honestly and he had the NERVE to flip me off (or some other gesture Idk). Im a calm guy, but really some people just dont deserve to have a license, let alone be allowed to drive on densely populated roads/highways. If youre gonna cut through lanes at least use the damn turn signal
    • HPA do an interesting video on tuning, and Adrian shows on the dyno, moving from 10:1 to 12:1 (And I think even 13:1) and the power moves SFA. However, a couple of degrees of timing has a HUGE impact. Exhaust side of things will more be the length of the exhaust and how many bends and turns you have. The straighter you can keep it, the better. By a lot. Oh, and getting the diameter right. Bigger isn't always better. Going to big can actually lose you power.
    • I have to say, most people I see on the road fit the bill of atrocious drivers. Whether they be cowboys in their dual cabs, bogans in the Commodores, or the soccer mums. Pretty much most people on the road put zero freaking thought into driving. Barely look further up the road then the end of their bonnet, and have never even thought about how catastrophically wrong shit can go, by doing what they all deem as normal driving. Especially their late braking, racing to stopped lights, and sitting half a foot off the bumper of the car in front at 110km/h. Wanna know what's even better? By the time their kids get to be old enough to learn to drive, they've already got in the back of their brain what is normal driving, how annoyed you're allowed to get at people etc, and then their parents who actually have zero freaking skill at driving (Even though they constantly say "I've been driving for 20 years and never had an accident!") teach the little twerps how to drive, or should I say, how to make a car move. Literally watched a parent teach their L Plater, on a 4 lane freeway, that you just slam the brakes on, and push your way over, even with a B Double bearing down on you, and that's how you should drive, rather then, just keep going to the next exit. Same shit happens all the time for side streets etc, watching numpties pull dumb shit turns pushing across 3 lanes of traffic, rather than just go up the road another 30 seconds, and take the next turn that'll get you to the same location... Oh, and the damn right lane bandits. Or the retards driving along with their headphones in, and can't hear the ambulance or fire truck right up their ass about to run them over...   Pretty much, people drive on the road, like ego centric f**ks, and don't actually think how dumb shit their driving is, how it could easily kill them or someone else in a split second, or at the very least, how they're driving is contributing to all the shit they're bitching about on the road, like shitty congestion!
×
×
  • Create New...