Jump to content
SAU Community

Recommended Posts

hey all, i gotta mate that reckons their vtec integra 1600cc automatic can go 280kmh... the speedo has been changed and i think the speed limiter 180kmh removed, so what is the top speed it could realistically do? i thought 230kmh might be possible,... anyone know for sure... i have an r32-t and know with the auto that 230 is tops, so the vteg surely cant do 280 in an auto am i right?

cheers all

ian

Link to comment
https://www.sau.com.au/forums/topic/83895-vtec-top-speed/
Share on other sites

well 280kmh sounds like a pretty tall story to me .my rb 25/30 de N/A conversion with 3.7 gears and .7 ratio 5th . does 14 .7 1/4 mile and best of a genuine 225 kmh at speed trials winding out over 3 miles . so that 280 kmh figure is " they gotta be dreamin !!! "

Link to comment
https://www.sau.com.au/forums/topic/83895-vtec-top-speed/#findComment-1519532
Share on other sites

I think you'll find the Integras that came in the vtec form, are not 1.6L for a start.

I've driven the DOHC 1.6L in a VTi-R coupe civic, and these hammer. Between a NA skyline, and a VTi-R coupe, its very close. However, these cars are geared for quick acceleration, which means top speed isn't that great.

The Australian delivered Honda's do not have limiters in them. 280 is a bit far fetched, but 230 is believable as i've been at 210 in an Integra Type R, and it still had a lot to go.

Hope this helps mate.

Dayne

Link to comment
https://www.sau.com.au/forums/topic/83895-vtec-top-speed/#findComment-1519996
Share on other sites

she reckons they did it on a air strip so room wasnt an issue, i just wouldnt beleive that the auto trans and let alone a 1600 would be able to push the car that farr, top gear in an auto would be redlining before it got up to 230 even wouldnt it? and it looked like a stock car pretty much...

Link to comment
https://www.sau.com.au/forums/topic/83895-vtec-top-speed/#findComment-1521013
Share on other sites

she  reckons they did it on a air strip so room wasnt an issue, i just wouldnt beleive that the auto trans and let alone a 1600 would be able to push the car that farr, top gear in an auto would be redlining before it got up to 230 even wouldnt it? and it looked like a stock car pretty much...

the 1.6L your talkling about is probly the LS integra DA9 teg

they run the same B16a as the Civic VTIR (coupe/hatch)

i am very doubt full it can hit 280km/h

in my old civic with a JDM B16a (more power LSD etc )

the very best i ran was 220km/h and the revs were sitting @ 7K rpm

and that was very scary for a old EG civic

anywayz i recon if it had the road max it'll ut out is probly 230-40 max

but it'll need a really really long long road

Link to comment
https://www.sau.com.au/forums/topic/83895-vtec-top-speed/#findComment-1521091
Share on other sites

Theoretical top speed for a R32 GTR is about 250km/h. Don't need a rocket scientist to figure out that a RB26DETT has more torque than a B16A engine. I don't care what aerodynamic coefficent a Intergra is it'll never reach 250km/h (unless a tornado is blowing wind in the right direction and plumetting down to earth from orbit, YES, it may reach 280km/h).

Just cause the speedo says, doesn't mean it can do!

Link to comment
https://www.sau.com.au/forums/topic/83895-vtec-top-speed/#findComment-1534849
Share on other sites

QUOTE(justin911 @ Aug 20 2005, 11:00 PM)

maybe your friends speedo got changed from km to mph and they didnt relise

that would be about 450kmh

that would be about 450kmh

:lol: pwend :lol: 416.666666666666666666667 actually :D

Edited by Pva_Glue
Link to comment
https://www.sau.com.au/forums/topic/83895-vtec-top-speed/#findComment-1538271
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...