Jump to content
SAU Community

Recommended Posts

she  reckons they did it on a air strip so room wasnt an issue, i just wouldnt beleive that the auto trans and let alone a 1600 would be able to push the car that farr, top gear in an auto would be redlining before it got up to 230 even wouldnt it? and it looked like a stock car pretty much...

They got a tow from a plane taking off. :lol:

Lets kill this one off right now, I don't have my Honda gear ratio chart with me, but from memory the manual B16A does 27 kph per 1,000 rpm. So 280 kph would be 10,370 rpm. So it's IMPOSSIBLE :)

But wait there is more ;)

If I remember rightly the auto is 8% shorter geared, so that would mean 11,200 rpm at 280 kph :lol:

:) cheers ;)

Edited by Sydneykid
whats a r32 gtrs stop speed btw?

I don't have my gear charts for Skylines with me either, again from memory 275kph = ~8,500 rpm. If it has enough power to push it there of course. At Philip Island we get to around 265 kph on the main straight which is somewhat downhill, and that's with 380 4wkw

:) cheers :)

hey. Its 12.20am and just got back from a burn in my mates s2k. THAT can definately do 280.... We onli took it up too 250 before i asked him to back it off. Thats a h22 in there but...

We took his type r integra up too 240 as well without too much of a sweat so i rekon it could do 280 without too much hassle. BUT i believe thats a b18 or sumthing in there.

That being said, it would barely be able to do 280 without some mods so i definatley dont think that a b16 could come close.

***all done on a legitimate track**** none of that open road shit.....

hey. Its 12.20am and just got back from a burn in my mates s2k. THAT can definately do 280.... We onli took it up too 250 before i asked him to back it off. Thats a h22 in there but...

Interesting, the F20 turns clockwise and the H22 turns anti clockwise, so that 250kph was in reverse, right? ;)

:) cheers :D

Theoretical top speed for a R32 GTR is about 250km/h. Don't need a rocket scientist to figure out that a RB26DETT has more torque than a B16A engine. I don't care what aerodynamic coefficent a Intergra is it'll never reach 250km/h (unless a tornado is blowing wind in the right direction and plumetting down to earth from orbit, YES, it may reach 280km/h).

Just cause the speedo says, doesn't mean it can do!

true but a type r teg is not far off. i was in my mates and we got it to 240km/h which i call close and damn good for a 1.8.

and yes i no at speeds like that that the speedo is not quite accurate but i am just saying what i have experianced. :P and civics have B16A integra B18C.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...